Register
Help
Remember Me?
What's New?
Activity Stream
New Posts
New Events
Mark Forums Read
Forum
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Filter by:
Last 7 Days
Clear All
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
8 Hours Ago
Dieselkid01
started a thread
Cm 2100
in
Cummins 6.7L
hi everyone, I have a cm2100 for my 6.7 build i want to run standalone. I have the firepunk standalone harness on c1 and c2. the ecm I have I was...
see more
0 replies | 18 view(s)
11 Hours Ago
Jim P
replied to a thread
2011 Base file
in
Cummins 6.7L
Cruise control functions won’t work
see more
3 replies | 156 view(s)
12 Hours Ago
Blacky
replied to a thread
May 20, 2024, V8.4.54 Public Release
in
Software Updates and Installation Help
Hi Koolky, Can you log a support ticket here: https://service.efilive.com/new-ticket Please include the appropriate trace file. Regards Paul
see more
2 replies | 244 view(s)
16 Hours Ago
aaronc7
replied to a thread
IAT Sensor Cal
in
Gen III V8 Specific
OK here it is for V7.5. Copy both .cax files to C:\Program Files (x86)\EFILive\V7.5\Calibrations\
see more
20 replies | 10035 view(s)
20 Hours Ago
dian
replied to a thread
logging not working
in
General
so wht happened (imo): first the (communication?) chip gave up the ghost. the system wrongly produced the "software/firmware incompatibility"...
see more
5 replies | 596 view(s)
20 Hours Ago
dian
replied to a thread
IAT Sensor Cal
in
Gen III V8 Specific
looking under v8, there is no "user defined cax8". (there is "user defined pids".) im not using v8. where should i copy it in v7.5? nothing with...
see more
20 replies | 10035 view(s)
1 Day Ago
koolky
replied to a thread
May 20, 2024, V8.4.54 Public Release
in
Software Updates and Installation Help
I'm getting error $0503 when trying to Cal flash an E40 ECM from V8. "Executing: C:\Program Files (x86)\EFILive\V8\Config\E40_W.obj" E40_W.obj is at...
see more
2 replies | 244 view(s)
1 Day Ago
Tony Bushmin
replied to a thread
2011 Base file
in
Cummins 6.7L
some functions may not work look on side of ecm for cm900xx.xx number that will help narrow down the right file
see more
3 replies | 156 view(s)
1 Day Ago
tim@minkhes.se
started a thread
Need help with MIL due to high TAP-values
in
Duramax 06 LLY / 06+ LBZ & LMM
Hi, We have a problems with EFILive on a Chevrolet Silverado Duramax (LMM) 2500HD 2008. The truck is not drivable due to fault codes set by the...
see more
0 replies | 31 view(s)
2 Days Ago
JtRenegade
replied to a thread
2011 Base file
in
Cummins 6.7L
What issues would arise if someone used the wrong basefile? like from a 2010 or 2012?
see more
3 replies | 156 view(s)
4 Days Ago
dianenelson
started a thread
Suggestion about coasting down to idle
in
Gen III V8 Specific
Hello, I have a LS1 Auto. The main problem i have i coasting at 40 to 70 km the idle hangs on at around 1100 rpm and the car doesn't slow down. I...
see more
0 replies | 61 view(s)
4 Days Ago
Lennydmaxguy
replied to a thread
bone stock c7 z06 2019 tune
in
E39, E80, E82 & E92 SIDI ECM's
Post your HP Tuners file. I can convert it to a ctz
see more
2 replies | 2079 view(s)
4 Days Ago
JtRenegade
started a thread
2011 Base file
in
Cummins 6.7L
Is there anyway to look up a base file with a VIN number? I have a whole mess of base files I have accumulated over the years but I'm not sure...
see more
3 replies | 156 view(s)
5 Days Ago
adam24v
started a thread
Medium Cam tuning
in
Gen III V8 Specific
Hey everyone, I am new here and have been playing with efi live for 5.9 and 6.7 cummins for a year now. This is my first time building a gasser and...
see more
0 replies | 60 view(s)
5 Days Ago
aaronc7
replied to a thread
IAT Sensor Cal
in
Gen III V8 Specific
Extract the two .cax8 file to C:\Users\XXXXX\XXXXXX\Documents\EFILive\V8\User Defined Cax8\LS1B open v8 editor, it should be located Engine...
see more
20 replies | 10035 view(s)
5 Days Ago
dian
replied to a thread
IAT Sensor Cal
in
Gen III V8 Specific
thank you so much.
see more
20 replies | 10035 view(s)
5 Days Ago
aaronc7
replied to a thread
IAT Sensor Cal
in
Gen III V8 Specific
I can't do it right this moment (on the road), but I can definitely help get you sorted with this. Should just be a simple drag and drop a cax file...
see more
20 replies | 10035 view(s)
6 Days Ago
maudyZ28
replied to a thread
bone stock c7 z06 2019 tune
in
E39, E80, E82 & E92 SIDI ECM's
BUMP really, no one had a 2019 Z06 they can go out and read? I did get a HP tuner version (I only have the software side), but even when...
see more
2 replies | 2079 view(s)
More Activity
No More Results
No Recent Activity