Search:

Type: Posts; User: 2006Cummins; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    29
    Views
    77,507

    Thanks for the reply Ross. I guess I am a little...

    Thanks for the reply Ross. I guess I am a little confused. I see in the release notes that this beta software that I installed supports CMF. I checked to be sure that the CMF .inx and .dat files were...
  2. Replies
    11
    Views
    8,303

    Just out of curiosity; it's not pressure that you...

    Just out of curiosity; it's not pressure that you are hearing, is it? I have found that too much pressure before boost causes a noticeable rattle. I have never been able to run enough timing to...
  3. Replies
    18
    Views
    9,863

    SOTP and smoke showed no noticeable change. Made...

    SOTP and smoke showed no noticeable change. Made a long log and after a quick review didn't see obvious changes.
  4. Replies
    18
    Views
    9,863

    Set the entire 6270 table to -5 and didn't see a...

    Set the entire 6270 table to -5 and didn't see a difference...
  5. Replies
    18
    Views
    9,863

    Any hints?

    Any hints?
  6. Replies
    129
    Views
    61,908

    I had been think of a setup like that too. The...

    I had been think of a setup like that too. The more more I thought about it, the more it seemed like it just might work. Thanks for putting the theory to life! Looking forward to seeing how it turns...
  7. Replies
    14
    Views
    11,383

    Ok, thanks. I'll watch the icon.

    Ok, thanks. I'll watch the icon.
  8. Replies
    14
    Views
    11,383

    I found that my problem is only when looking at...

    I found that my problem is only when looking at charts on the dashboard - it doesn't show any data when connected and the yellow monitor button is pushed, but does when recording. I can monitor data...
  9. Replies
    14
    Views
    11,383

    No real time data...

    No real time data...
  10. Replies
    14
    Views
    11,383

    I am having a similar problem also. I can record...

    I am having a similar problem also. I can record just fine, but cannot monitor. When I hit the yellow button it says that it's paused, and does nothing. It has been this way for a couple of months I...
  11. Replies
    10
    Views
    8,883

    I enabled mine with a starscan a while back....

    I enabled mine with a starscan a while back. Whenever I flash with efi it goes away. I have to re-enable it with my programmer if I want it to work.
  12. Replies
    128
    Views
    81,736

    Worked for me. Thanks!

    Worked for me. Thanks!
  13. Replies
    128
    Views
    81,736

    I will give that a try, thanks.

    I will give that a try, thanks.
  14. Replies
    128
    Views
    81,736

    Just updated to the latest public v7.5 and v8...

    Just updated to the latest public v7.5 and v8 software release, and checked for updates. Firmware: 2.07.26 (Mar 28, 2012). Bootblock: 2.07.04 (Dec 12, 2011). Config files: cummins cm849 (apr 16...
  15. Replies
    48
    Views
    23,218

    12896[/attach [attach=config]12897

    12896[/attach

    [attach=config]12897
  16. Thread: Csp?

    by 2006Cummins
    Replies
    22
    Views
    16,366

    Ok, ok, so it is not really NEEDED. But, I don't...

    Ok, ok, so it is not really NEEDED. But, I don't NEED 600hp either.;) My reason for WANTING it is to help with tuning. I can have my current tune on one setting, and then have four other slightly...
  17. Thread: Csp?

    by 2006Cummins
    Replies
    22
    Views
    16,366

    Thanks.

    Thanks.
  18. Thread: Csp?

    by 2006Cummins
    Replies
    22
    Views
    16,366

    Csp?

    Just wondering if there is a rough time frame when we will see switchable tuning for cummins. I am really looking forward to this to help with tuning.

    Mike
  19. Replies
    4
    Views
    3,742

    Thanks. I'm really looking forward to switchable...

    Thanks. I'm really looking forward to switchable tuning so that we can try a few things during one quick dyno session. Again, thanks for your help.
  20. Replies
    4
    Views
    3,742

    Hi, Les. It started out as the first tune you...

    Hi, Les.

    It started out as the first tune you sent me, and I have made 53 revisions to it since then.


    No, it was a dynojet 248c


    With my dyno experience I would agree that correction...
  21. Replies
    4
    Views
    3,742

    Progress Update: Dyno Run

    Made a couple of dyno runs at the ITD dyno day this weekend. I'm about where I wanted to be for power, but still have some work to do. I was hoping to get a good video of the run to watch smoke, but...
  22. Replies
    9
    Views
    11,846

    Dyno run 3/17/12: http://youtu.be/4CTWZ2z_YYg

    Dyno run 3/17/12:


    http://youtu.be/4CTWZ2z_YYg
  23. Replies
    60
    Views
    40,055

    Thanks for the help guys. It's working now!

    Thanks for the help guys. It's working now!
  24. Replies
    60
    Views
    40,055

    Ok, I was able open config under V8 while in the...

    Ok, I was able open config under V8 while in the V8 tune tab. I found cm849 and programmed that to the V2. Now, the options file under config in the V2 says march 12th, but there are no config files...
  25. Replies
    60
    Views
    40,055

    I just opened the V8 with the V2 connected, hit...

    I just opened the V8 with the V2 connected, hit f5, then f3. There is no "cmb" to select - just a page of "unused." The "config files" listed under the efilive explorer are dated jan 18th, jan 5th,...
Results 1 to 25 of 134
Page 1 of 6 1 2 3 4