Register
Help
Remember Me?
What's New?
Activity Stream
New Posts
New Events
Mark Forums Read
Forum
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Filter by:
Last 7 Days
Clear All
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
2 Days Ago
nonnieselman
replied to a thread
Medium Cam tuning
in
Gen III V8 Specific
????
see more
11 replies | 544 view(s)
3 Days Ago
adam24v
replied to a thread
Medium Cam tuning
in
Gen III V8 Specific
Sorry, whenever I try to post a reply on my phone it never posts it properly and cuts off a giant section of the paragraph or the whole thing. As...
see more
11 replies | 544 view(s)
3 Days Ago
nonnieselman
replied to a thread
IAT Sensor Cal
in
Gen III V8 Specific
You dont make the folder, its already there. Look under your C: Drive\Program Files (x86)\EFILive\V7.5 Folder. This is where your CAX files go.
see more
26 replies | 10860 view(s)
3 Days Ago
nonnieselman
replied to a thread
Medium Cam tuning
in
Gen III V8 Specific
Yea ive done hundreds of turbo trucks with OLSD. It works, just takes time to get the tune sorted out. Your COS3 now is fine. Make sure your...
see more
11 replies | 544 view(s)
3 Days Ago
adam24v
replied to a thread
Medium Cam tuning
in
Gen III V8 Specific
Alright so i've been messing with the car and it idles well or atleast better than before. I've also torn it back down though and began the piping...
see more
11 replies | 544 view(s)
3 Days Ago
ccclose
replied to a thread
Fuel control states list
in
Cummins 6.7L
I finally found the Cummins slide show for CMD, thanks I can share it if anyone is interested
see more
5 replies | 2095 view(s)
3 Days Ago
Jim P
replied to a thread
Fuel control states list
in
Cummins 6.7L
Different for the CMD, CME and CMF
see more
5 replies | 2095 view(s)
4 Days Ago
ccclose
replied to a thread
Fuel control states list
in
Cummins 6.7L
I need help deciphering this thanks!
see more
5 replies | 2095 view(s)
5 Days Ago
dan_verbruggen@live.com
replied to a thread
2015 LML Stock Tune
in
Duramax 2011+ LML / LGH
thanks alot
see more
2 replies | 2178 view(s)
5 Days Ago
jakezed22
replied to a thread
LML will not go over 101.5 MM3
in
Duramax 2011+ LML / LGH
What part?
see more
10 replies | 7301 view(s)
6 Days Ago
Blacky
replied to a thread
Selecting Cells
in
V8 Tune Editor
Why not just select all the cells you want to adjust and adjust them all at the same time? You can select non-rectangular areas using the Ctrl key,...
see more
4 replies | 11125 view(s)
6 Days Ago
bondmatos
replied to a thread
Selling All of my Tested and Pre Built Files
in
General (Diesel)
Are you still selling all of this files?
see more
5 replies | 1544 view(s)
6 Days Ago
oztracktuning
replied to a thread
Selecting Cells
in
V8 Tune Editor
is it possible to select maybe 5-10 cells in the VVE table and be able to adjust them then press the PGDn key and have the selected cells move...
see more
4 replies | 11125 view(s)
6 Days Ago
andysc3
replied to a thread
New to me 2014 Chevy Cruze 1.4T, need advice on where to start
in
E78, E83, E84 PFI ECM's
yes, it's on my list to get. will have one by the end of the month. I picked up the zzp catless 02 pipe and mid pipe. But getting a p0598 code for...
see more
3 replies | 290 view(s)
More Activity
No More Results
No Recent Activity