Activity Stream - EFILive Forum

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

1 Hour Ago

ScarabEpic22 replied to a thread 2013 5.3L Magnuson cal needed- in E37, E38 & E67 PFI ECM's

Post the VIN and/or OS, someone may be able to provide a clean base calibration for you.

4 replies | 32 view(s)

23 Hours Ago

Blacky replied to a thread March 2021, V8.3.5 Beta 4 in Software Updates and Installation Help

Yes, I can confirm the boot block update via the EFILive Control Panel does have a problem - it will be fixed in the next update. Instead of using...

2 replies | 223 view(s)

1 Day Ago

GreenDiesel replied to a thread March 2021, V8.3.5 Beta 4 in Software Updates and Installation Help

It seems there is an issue with updating the V2 firmware using this software release. On 3 laptops now when trying to do the firmware update it says...

2 replies | 223 view(s)

1 Day Ago

mysunnshine replied to a thread 2013 5.3L Magnuson cal needed- in E37, E38 & E67 PFI ECM's

I will agree but I do not have a stock cal and I do not have a clean version of the Magnuson version.

4 replies | 32 view(s)

1 Day Ago

In-Tech replied to a thread 2013 5.3L Magnuson cal needed- in E37, E38 & E67 PFI ECM's

I will double agree with that comment :Throwup: :grin: :grin:

4 replies | 32 view(s)

1 Day Ago

minytrker replied to a thread 2013 5.3L Magnuson cal needed- in E37, E38 & E67 PFI ECM's

You would be better starting over from stock. I wouldnt use the magnuson tune or anything from it.

4 replies | 32 view(s)

1 Day Ago

mysunnshine started a thread 2013 5.3L Magnuson cal needed- in E37, E38 & E67 PFI ECM's

Would anyone out there have a base cal for the Magnuson TVS1900 on a 2013 5.3L by chance? Somebody had their hand at this truck before me and I...

4 replies | 32 view(s)

1 Day Ago

Blacky started a thread March 2021, V8.3.5 Beta 4 in Software Updates and Installation Help

ATTENTION - BETA SOFTWARE RELEASE We strongly recommend that you do not install the beta software ...

2 replies | 223 view(s)

1 Day Ago

RC1 replied to a thread 2014 E92 standalone questions in E39, E80, E82 & E92 SIDI ECM's

Dorman 902-310 is the fan control relay number, and I believe it's expecting PWM- signal. I haven't messed with it for a while, but let me know if...

10 replies | 267 view(s)

2 Days Ago

RADustin replied to a thread 2014 E92 standalone questions in E39, E80, E82 & E92 SIDI ECM's

you are awesome, thanks. yeah I may need to drop my o-scope on the cooling fan wire to learn about it. does the jeep controller expect a...

10 replies | 267 view(s)

2 Days Ago

wait4me replied to a thread February 2021, V8.3.5 Beta 3 in Software Updates and Installation Help

7.5 is broken so wait for fix. Probably should not flash with it as it has been causing issues on full flashes. V8 version is fine

3 replies | 218 view(s)

2 Days Ago

RC1 replied to a thread 2014 E92 standalone questions in E39, E80, E82 & E92 SIDI ECM's

X1 pin 44 will control a fuel pump in the way we're used to with the old ECM's, in that it will prime the pump for a couple of seconds prior to...

10 replies | 267 view(s)

3 Days Ago

Blacky replied to a thread February 2021, V8.3.5 Beta 3 in Software Updates and Installation Help

I think that would be possible. Regards Paul

3 replies | 218 view(s)

3 Days Ago

Mitco39 replied to a thread February 2021, V8.3.5 Beta 3 in Software Updates and Installation Help

Would it be possible to add a shortcut to the "Load All Security Restions From Another File" Option? I use this a ton and adding a shortcut (perhaps...

3 replies | 218 view(s)

3 Days Ago

raceghost replied to a thread Improving shifts via the ECM in 6 speed/8 speed RWD/FWD Transmission Tuning (incl T43, T76, T87)

Well, after a lot of digging and comparison, I have answered my own question. I hope this will help all of you, and OP, you may want to add this to...

151 replies | 110687 view(s)

3 Days Ago

Blacky started a thread February 2021, V8.3.5 Beta 3 in Software Updates and Installation Help

ATTENTION - BETA SOFTWARE RELEASE We strongly recommend that you do not install the beta software over ...

3 replies | 218 view(s)

3 Days Ago

GMPX replied to a thread Dodge Cummins 2350B delete in Cummins 6.7L

Actually that is a bug in the particular version of V7 you have there. You should be getting message that the OS is not supported. Reason being is...

4 replies | 175 view(s)