ls1vt209
February 16th, 2009, 02:17 AM
:help2:
Please help any assistance is greatly appreciated. I also apologise in advance for the length of this post.
Ok tonight a mate came over and I flashed a tune into his E38. The cal was from another car which I had spent much time on configing. Both vehicles are LILPG powered Holdens with L98's, both 6l80E's. Both are 2006 models.
Anyway I flash in the cal's (I must admit without removing the original cal first, brain snap and forehead slap for me I know) no problem. Drive 40km up the road stop for a short time after reading logs etc, no problems. Go to flash in another Cal and PCM packs it in. I again go to flash the cal in and get the following
'21:28:20.968: Interface firmware version: 2.6.5
21:28:20.984: Interface firmware model: FSV2
21:28:21.000: Interface firmware version: 2.6.5
21:28:21.015: Interface firmware date: Oct 28, 2008
21:28:21.015: FlashScan serial number: 003689852244
21:28:21.031: FlashScan license number: 003689852244
21:28:21.046: Disconnecting ...
21:28:21.703: CAN-VPW Bridge Deactived
21:28:21.703: Disconnected
21:28:22.359: Scanning for EFILive FlashScan V2 USB
21:28:24.781: Scanning for EFILive FlashScan V2 HAPI
21:28:24.968: Interface firmware version: 2.6.5
21:28:24.968: CAN-VPW Bridge Actived
21:28:25.000: Current protocol set to: "ISO 15765 CAN"
21:28:27.046: Current protocol: "ISO 15765 CAN"
21:28:27.062: Interface firmware model: FSV2
21:28:27.078: Interface firmware version: 2.6.5
21:28:27.093: Interface firmware date: Oct 28, 2008
21:28:27.109: FlashScan serial number: 003689852244
21:28:27.125: FlashScan license number: 003689852244
21:28:29.203: Interface firmware version: 2.6.5
21:28:31.250: Getting status...
21:28:32.265: Status: Calibration missing.
21:28:50.250: Bootloader version: E38a_v1.6C (0C56-F506)
21:28:50.265: Preparing ECM for reflash...
21:28:50.281: ECM reports "Not secured!"
21:28:50.281: Initializing ECM...
21:28:51.515: Initializing ECM, step 1 of 4
21:28:51.515: Initializing ECM, step 2 of 4
21:28:52.750: Initializing ECM, step 3 of 4
21:28:55.203: Initializing ECM, step 4 of 4
21:28:55.625: Initializing bootloader...
21:28:55.906: Initializing bootloader, step 1 of 7
21:28:56.250: Initializing bootloader, step 2 of 7
21:28:56.593: Initializing bootloader, step 3 of 7
21:28:56.937: Initializing bootloader, step 4 of 7
21:28:57.281: Initializing bootloader, step 5 of 7
21:28:57.625: Initializing bootloader, step 6 of 7
21:28:57.968: Initializing bootloader, step 7 of 7
21:28:58.968: ECM ready for reflashing.
21:28:59.078: Request GM operating system...
21:28:59.093: GM operating system: 12612381
21:28:59.843: Request serial number...
21:28:59.906: Serial number: 86K16169B4AX
21:29:00.812: Erasing ECM flash memory... (please wait up to 120 seconds)
21:29:05.062: Flash chip could not be programmed.
21:29:05.296: Checksum of flash failed after write completed. Please reflash the controller.
21:29:05.328: ECM is in an unknown state.
21:29:07.437: Clear emisison related DTCs...
21:29:09.500: Interface firmware version: 2.6.5
21:29:10.531: Clear DTCs for all modules...
21:29:12.578: Interface firmware version: 2.6.5
21:29:13.843: Disconnecting ...
21:29:14.484: CAN-VPW Bridge Deactived
21:29:14.500: Disconnected
21:29:14.500: Reflash failed.
21:29:20.578: Done!'
So basically it is telling me that there is no Cal in there and that I need to flash another one in. So I try again, still no luck, try again and again with no glory. So I contact a couple of well known Pro tuners and they both give me advice which I follow still no luck. I also attempted to read the tune in the PCM and there is absolutely no cals loaded at all, read came back empty. See attached.
I also got this message,
This version of the EFILive Tuning Tool has not been
configured to display this PCM's operating system.
This may occur if...
your PCM has been updated by a GM dealer
to fix a software problem in the PCM.
OR
you are attempting to load an EFILive custom PCM
program without installing the matching *.cal file.
OR
you are attempting to load a non-EFILive custom PCM program.
Please save this calibration's *.tun file
and email a copy of it to: support@efilive.com
so that we can add support for it.
The car will not start etc.
I have tried multiple times to flash in the cal, I have tried a full reflash, nothing seems to work. The car drove perfect from the initial flash but once I tried to flash in some changes that is when the problems occured. BTW there was no voltage changes, eg radio, windows etc used whilst flashing.
Please help any advice is greatly appreciate, I have never had a problem like this before.
BTW Thanks to Jezza and Steve from Oztrack, I appreciate the time and advice gents.
Please help any assistance is greatly appreciated. I also apologise in advance for the length of this post.
Ok tonight a mate came over and I flashed a tune into his E38. The cal was from another car which I had spent much time on configing. Both vehicles are LILPG powered Holdens with L98's, both 6l80E's. Both are 2006 models.
Anyway I flash in the cal's (I must admit without removing the original cal first, brain snap and forehead slap for me I know) no problem. Drive 40km up the road stop for a short time after reading logs etc, no problems. Go to flash in another Cal and PCM packs it in. I again go to flash the cal in and get the following
'21:28:20.968: Interface firmware version: 2.6.5
21:28:20.984: Interface firmware model: FSV2
21:28:21.000: Interface firmware version: 2.6.5
21:28:21.015: Interface firmware date: Oct 28, 2008
21:28:21.015: FlashScan serial number: 003689852244
21:28:21.031: FlashScan license number: 003689852244
21:28:21.046: Disconnecting ...
21:28:21.703: CAN-VPW Bridge Deactived
21:28:21.703: Disconnected
21:28:22.359: Scanning for EFILive FlashScan V2 USB
21:28:24.781: Scanning for EFILive FlashScan V2 HAPI
21:28:24.968: Interface firmware version: 2.6.5
21:28:24.968: CAN-VPW Bridge Actived
21:28:25.000: Current protocol set to: "ISO 15765 CAN"
21:28:27.046: Current protocol: "ISO 15765 CAN"
21:28:27.062: Interface firmware model: FSV2
21:28:27.078: Interface firmware version: 2.6.5
21:28:27.093: Interface firmware date: Oct 28, 2008
21:28:27.109: FlashScan serial number: 003689852244
21:28:27.125: FlashScan license number: 003689852244
21:28:29.203: Interface firmware version: 2.6.5
21:28:31.250: Getting status...
21:28:32.265: Status: Calibration missing.
21:28:50.250: Bootloader version: E38a_v1.6C (0C56-F506)
21:28:50.265: Preparing ECM for reflash...
21:28:50.281: ECM reports "Not secured!"
21:28:50.281: Initializing ECM...
21:28:51.515: Initializing ECM, step 1 of 4
21:28:51.515: Initializing ECM, step 2 of 4
21:28:52.750: Initializing ECM, step 3 of 4
21:28:55.203: Initializing ECM, step 4 of 4
21:28:55.625: Initializing bootloader...
21:28:55.906: Initializing bootloader, step 1 of 7
21:28:56.250: Initializing bootloader, step 2 of 7
21:28:56.593: Initializing bootloader, step 3 of 7
21:28:56.937: Initializing bootloader, step 4 of 7
21:28:57.281: Initializing bootloader, step 5 of 7
21:28:57.625: Initializing bootloader, step 6 of 7
21:28:57.968: Initializing bootloader, step 7 of 7
21:28:58.968: ECM ready for reflashing.
21:28:59.078: Request GM operating system...
21:28:59.093: GM operating system: 12612381
21:28:59.843: Request serial number...
21:28:59.906: Serial number: 86K16169B4AX
21:29:00.812: Erasing ECM flash memory... (please wait up to 120 seconds)
21:29:05.062: Flash chip could not be programmed.
21:29:05.296: Checksum of flash failed after write completed. Please reflash the controller.
21:29:05.328: ECM is in an unknown state.
21:29:07.437: Clear emisison related DTCs...
21:29:09.500: Interface firmware version: 2.6.5
21:29:10.531: Clear DTCs for all modules...
21:29:12.578: Interface firmware version: 2.6.5
21:29:13.843: Disconnecting ...
21:29:14.484: CAN-VPW Bridge Deactived
21:29:14.500: Disconnected
21:29:14.500: Reflash failed.
21:29:20.578: Done!'
So basically it is telling me that there is no Cal in there and that I need to flash another one in. So I try again, still no luck, try again and again with no glory. So I contact a couple of well known Pro tuners and they both give me advice which I follow still no luck. I also attempted to read the tune in the PCM and there is absolutely no cals loaded at all, read came back empty. See attached.
I also got this message,
This version of the EFILive Tuning Tool has not been
configured to display this PCM's operating system.
This may occur if...
your PCM has been updated by a GM dealer
to fix a software problem in the PCM.
OR
you are attempting to load an EFILive custom PCM
program without installing the matching *.cal file.
OR
you are attempting to load a non-EFILive custom PCM program.
Please save this calibration's *.tun file
and email a copy of it to: support@efilive.com
so that we can add support for it.
The car will not start etc.
I have tried multiple times to flash in the cal, I have tried a full reflash, nothing seems to work. The car drove perfect from the initial flash but once I tried to flash in some changes that is when the problems occured. BTW there was no voltage changes, eg radio, windows etc used whilst flashing.
Please help any advice is greatly appreciate, I have never had a problem like this before.
BTW Thanks to Jezza and Steve from Oztrack, I appreciate the time and advice gents.