I can't read a tune, but can flash one

[dlove]

V2, I have all the latest updates and firmware. I believe...

V2- 2.06.02
Tune Tool- Build 88

If I go to read a tune, it gets all the way to the part where it would start to move the process bar. But once it would start to read, the bar does not show up and nothing happens. If I wait a few mins it finally stops itself and suggest trying slow mode. That has the same results.

I can flash in a tune without any issue.

Help.

[joecar]

Hi dlove,

What vehicle did this happen on...?

Can you copy the log text and paste it here...

[dlove]

Happened on a 04 silverado. And an fbody I think it was.

What log text do you mean? I can zip the bug reports if you want.

[joecar]

When you read or write a tune, a box pops up and shows a log of what is going on... see attached image... you can copy/paste the text from that box.

you may have to disable the 15 second countdown message:
in tunetool go Edit->Properties->Options and uncheck "Show timer countdown after read/reflash".

:)

[dlove]

17:36:32.489: Scanning for EFILive FlashScan V2 USB
17:36:34.919: Scanning for EFILive FlashScan V2 HAPI
17:36:35.124: Interface firmware version: 2.6.10
17:36:35.164: Interface firmware model: FSV2
17:36:35.184: Interface firmware version: 2.6.10
17:36:35.204: Interface firmware date: May 25, 2009
17:36:35.219: FlashScan serial number: 003744787534
17:36:35.244: FlashScan license number: 00359117917
17:36:35.284: Disconnecting ...
17:36:35.679: CAN-VPW Bridge Deactivated
17:36:35.684: Disconnected
17:36:36.294: Scanning for EFILive FlashScan V2 USB
17:36:38.719: Scanning for EFILive FlashScan V2 HAPI
17:36:38.929: Interface firmware version: 2.6.10
17:36:38.949: CAN-VPW Bridge Activated
17:36:38.979: Current protocol set to: "SAE J1850 VPW"
17:36:40.069: Current protocol: "SAE J1850 VPW"
17:36:40.109: Interface firmware model: FSV2
17:36:40.129: Interface firmware version: 2.6.10
17:36:40.149: Interface firmware date: May 25, 2009
17:36:40.169: FlashScan serial number: 003744787534
17:36:40.189: FlashScan license number: 00359117917
17:36:40.299: Getting status...
17:36:40.339: Status: OK.
17:36:41.214: Bootloader version: LS1B_v1.7R (04DA-6638)
17:36:41.214: Preparing PCM for reading flash...
17:36:41.259: PCM seed is: $7DFA
17:36:41.259: Unlock attempt 1 of 1
17:36:41.394: Initializing PCM...
17:36:42.164: Initializing PCM, step 1 of 4
17:36:42.164: Initializing PCM, step 2 of 4
17:36:42.944: Initializing PCM, step 3 of 4
17:36:44.459: Initializing PCM, step 4 of 4
17:36:44.894: Initializing bootloader...
17:36:45.204: Initializing bootloader, step 1 of 3
17:36:45.579: Initializing bootloader, step 2 of 3
17:36:45.959: Initializing bootloader, step 3 of 3
17:36:46.459: PCM ready for reading flash.
17:36:46.579: Intel AB28F400B - 512K
17:40:28.699: Stopping, please wait...
17:40:34.539: Total time: 03:47
17:40:34.544: Rebooting PCM... (please wait up to 8 seconds)
17:40:35.694: PCM has booted successfully...
17:40:36.694: Clear emisison related DTCs...
17:40:36.724: Clear DTCs for all modules...
17:40:37.614: Disconnecting ...
17:40:38.019: CAN-VPW Bridge Deactivated
17:40:38.024: Disconnected
17:40:40.859: Done!

in the picture is where it sits without doing anything. I have read a couple hundred tunes or so. I'm not sure if I accidentally messed up something with the V2 or what.

I tired to take off the 15 second timer, but no luck.

[Blacky]

Try the latest pre-release, it has many, many updates and bug fixes.
Don't forget to upgrade your FlashScan firmware to V2.06.16
http://forum.efilive.com/showthread.php?t=12014

Regards
Paul

[dlove]

the update fixed it

[Blacky]

Good to know. Thanks for the feedback.
Regards
Paul