PDA

View Full Version : Can't log some airflow PIDs



O1Z06
February 15th, 2011, 03:21 PM
I am not able to log RAFIG or RAFPN because I can't select the required LTD and STD airflow, is this because I have a M6? In absense of logging RAF, I used IACDES_B (ETC) v.s. ECT to map a base airflow but when I map DYNAIR v.s. ECT they are about 2 grams/s lower. Which one should I use? It is idling great at 900rpm with IACDES_B map airflow.

I also can't log cracker and follower PID's.:confused:

O1Z06
February 18th, 2011, 08:20 AM
I am still not having any luck. Are there any other PIDs that will activate stit and ltit that I am not selecting? My idle is very nice as I have done about 30 cold start logs to get it as good as its gonna get but I have been reading all this about RAFIG stuff and wanted to give it a try just for kicks and nick knacks. I am running OL 1Bar SD right now. Anyone want to shoot an idea?

joecar
February 18th, 2011, 09:30 AM
I take it you already did Validate Pids.

joecar
February 18th, 2011, 09:38 AM
On the PIDs tab, if you do rightclick->More Info on those pids they will show you which other pids you need to select...

Are you saying those other pids are not selectable...?

Do this:
- go File->Enter VIN and enter your VIN and OS id (available from tune file);
- go File->Select Controller and choose 1999-2008 GenIII LS1B;
- go Info->Validate PIDs;

then see if these pids show up:
- GM.IAC_LTD_DMA,
- GM.IAC_STD_DMA,
- GM.IAC_LTPB_DMA,
- GM.IAC_STPN_DMA.

O1Z06
February 18th, 2011, 12:20 PM
Yes that is correct, if I right click RAFIG it reads stit and ltit but I can only see RAFIG, STIT, and LTIT if I uncheck the supported box. I followed your instructions all while connect to the PCM as that is the only way to validate PIDs and still could not select LTIT and STIT. So something is not right. I am also not able to select throttle cracker and follower airflow PIDs. If it helps I am running COS 02040003.

joecar
February 18th, 2011, 02:27 PM
Click on the column heading "Caption", the pid list should now appear sorted alphabetically on the Caption column...

you can now look down the Caption column to find those pids.

What was the OEM OS that 02040003 goes with...? [ not all OS's have the _DMA pids defined ]

O1Z06
February 18th, 2011, 03:46 PM
OEM operating system is 12593358

Tordne
February 20th, 2011, 07:13 AM
I can see there are very few DMA PIDs defined for the 12593358 OS. Are you able to run the 12212156 OS? That is one of the most supported LS1 PCM operating systems.

Taz
February 20th, 2011, 07:43 AM
OS 12593358 was used in 2001 to 2003 Corvettes with the LS1 or LS6 (Z06) and equipped with a manual transmission.

OS 12212156 was used in 2002 Corvettes with the LS1 and equipped with a 4L60 (A4) transmission. Obviously this OS was also used numerous other platforms - including the 2002 Camaro with both the 4L60 and manual transmissions.

To use OS 12212156 in this particular vehicle, you would need to begin with the 2002 Corvette LS1 4L60 tune, swap in the manual segment from a 2002 Camaro, then copied over the LS6 specific parameters into the LS1 tune.

Then applied whichever COS suited the intended purpose.

I have never done this … rarely work on Corvettes … merely thinking out loud …


Regards,
Taz

Tordne
February 20th, 2011, 07:57 AM
12212156 was also used in the 2002 Corvette/Camaro with the manual. So shouldn't require the segment swap necessarily.

Taz
February 20th, 2011, 08:11 AM
You are very correct … checked the Holdencrazy site … there is a 2002 Corvette LS1 manual tune on file using OS 12212156. I didn’t have one on file - I don’t work on enough Corvettes it seems !!


Regards,
Taz

Tordne
February 20th, 2011, 08:20 AM
Back when I had my LS1 I was intimately familiar with all the LS1 operating systems :). The 12212156 I remember fondly cause it was what all my US friends were pretty much running, plus it's the one we can the COS5 for as well.

Anyway, O1Z06 changing to 12212156 would be what it'd recommend if possible.

O1Z06
February 20th, 2011, 02:50 PM
Ok thanks guys. Sorry for the noob question but could you list the steps to get from my current COS 02040003 to 12212156 then back to COS. Thanks again.

Tordne
February 20th, 2011, 03:02 PM
Pretty much the following are required:
1. Grab a 12212156 manual from my Holden Crazy site (if that's what you need).
2. Open your current calibration and the new 12212126 that you're going to use in two instances of the Tun Tool (side-by-side).
3. The boring part; copy and paste from your calibration into the 12212156 OS.
4. Full-flash in the 02020003 or 02020005 COS.
5. Cal-flash in the new 12212156 OS you've copied all the tables to.
6. Read out the PCM and save the new file as your base for ongoing modification.
7. Check the COS specific tables to make sure they have sane values (probably copy and paste again).
8. Cal flash in again with any changes.

Then as normal from there...

O1Z06
February 20th, 2011, 04:17 PM
Easy as pi, thank you Andrew. The part I was a little fuzzy on was the "boring part" but I got it now. It's too bad the load alternate calibration for comparison will not work because of the differences in the VINs but for every other instance that is probably a good thing.

Tordne
February 20th, 2011, 04:46 PM
The compare is limited to the same OS # in V7. In V8 that won't be a limitation :-)

joecar
February 21st, 2011, 04:03 AM
In the boring part: use copy-with-labels and past-with-labels (this aligns the paste correctly, avoids human misalignment).

There might be a table or two that won't past like this, just eyeball those and use common sense.