New laptop connection troubles

[eboggs_jkvl]

Error report generated by EFILive at 11:17:16 on Dec 29, 2005

Error code: ERR_RESPONSE/5
Response $31: "Request Out of Range".

EFILive Version: 7.3.0 (Build 314)

Platform: Windows XP
Version: 5.1 (build 2600)
Processor type: Pentium 798MHz

Directories
Temporary Cache: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Temporary cache
Logged Data: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Logged data
Customers: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Customers
Configuration: C:\Program Files\EFILive\V7\Configuration
Exported Data: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Exported data
Images: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Images
Sounds: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Sounds
Maps: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Maps
Pids: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\PIDs
Virtual Dash: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\VDash
Print Reports: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Print reports
Bug Reports: C:\Documents and Settings\Eboggs\My Documents\EFILive\V7\Bug reports

Connected: No
Com port: 0
Com setup: EFILive FlashScan FSP: USB
Requested baud rate: 115200

Cable id: 4
Cable code: FlashScan V1
Cable desc: EFILive FlashScan FSP
Cable version: 1.2.17
Cable Firmware date: 20050118
Cable model: FSP
Cable Serial number: 003528284029

Protocols: 0
Protocol list:

Auto connect: No
Scan OBDII info: No

Error retries: 1
Retry delay: 10
Message throttle: 0

Most recently used VIN: 2G1FP22G0W2xxxxxx (Note: 1)

PCM information
PCM HDW Number: 16239740
Calibration ID: 9375621
Serial Number: 0J0RY2724600
Operating System: 19980100
Engine Calibration: Unknown
Engine Diagnostics: Unknown
Transmission Calibration: Unknown
Transmission Diagnostics: Unknown
Fuel System: Unknown
System: Unknown
Speedometer: Unknown
Operating System BCC: Unknown
Stream-Slow scan mode: Supported
Stream-Fast scan mode: Supported
Maximum dynamic packets: 16

Detected modules:
$10="Powertrain Control Module (PCM)"

Selected parameters:
CALC.INJDC1=1,0
CALC.INJDC2=1,2
GM.FTC=1,19
GM.HO2S11=1,4
GM.HO2S12=1,15
GM.HO2S21=1,5
GM.HO2S22=1,16
GM.IAC=1,17
GM.IBPW1=1,6
GM.IBPW2=1,7
GM.INJ1PW=1,18
GM.KR=1,12
GM.TP=1,14
GM.TPS=1,13
SAE.ECT=1,3
SAE.IAT=1,8
SAE.LONGFT1=1,10
SAE.LONGFT2=1,11
SAE.MAP=1,9
SAE.RPM=1,1
SAE.SPARKADV=1,20
SAE.VSS=1,21

Most recent communication with vehicle:
10:57:25.187 Send: $A1,$23,$00,$01,$00,$C5
10:57:25.187 Recv: $B1,$A3,$00,$00,$54
10:57:25.187 Send: $A1,$40,$00,$06,$0C,$6C,$10,$F1,$2A,$00,$8A
10:57:25.203 Recv: $B1,$C0,$00,$05,$6C,$F1,$10,$6A,$00,$4D
10:57:25.203 Send: $A1,$23,$00,$01,$00,$C5
10:57:25.203 Recv: $B1,$A3,$00,$00,$54
10:57:25.203 Send: $A1,$02,$00,$00,$A3
10:57:25.203 Recv: $B1,$82,$00,$04,$46,$53,$50,$00,$20ty of the report.

[eboggs_jkvl]

Ooooorah! I'm gettin better at this stuff. Found the culprit. It was marked as a valid PID but the software got into a hissy fit with it selected. No sweat.


Elmer

[Blacky]

Ooooorah! I'm gettin better at this stuff. Found the culprit. It was marked as a valid PID but the software got into a hissy fit with it selected. No sweat.


Elmer

Which PID, was it a DMA PID?
Paul

[eboggs_jkvl]

Injector Pulse Width Injector 1 INJ1PW

I had that selected and it gave me error 31 when I tried to go to "record". I managed to get the old laptop to run another time (Getting real hard to do that) and simply compared PID to PID what was on the old VS the new and found that 1 difference.

Elmer

[Blacky]

The 8 injector pulse width PIDs are for Diesels.
For petrol engines use: {GM.IBPW1} and {GM.IBPW2}.

Have you run the PID validation (Shift+F2) after connecting to your 98? Those 8 injector pulse width PIDs should not be marked valid.

Regards
Paul

[eboggs_jkvl]

Yepper! I've run that rascal 3 or 4 times

[eboggs_jkvl]

Here's the little cutie allowing me to select it and there isn't a diagonal line on the icon indicating that it's non-valid.

[Blacky]

Can you please run it again and when it is finished, generate a user error report (menu: File->Generate error report) and then send the error report to me at paul@efilive.com. Thanks.

Regards
Paul

[eboggs_jkvl]

You've got mail

[eboggs_jkvl]

You've got more mail. I followed instructions this time!

[eboggs_jkvl]

Paul e-mailed me a cigar. I get the "Why the hell is it doing that?" award for this week! Whoopie!


Elmer