need help with v2 not read pid list

[restless@westnet.com.au]

i am trying to get a new v2 to log the E38 pid list in a new E3 hsv maloo
i have set up two others recently all with the same pid list with no trouble
the v2 works in my E1 hsv maloo
but not in the E3
and my own v2 witch i have been using for over two years now WONT WORK in the new E3 hsv maloo
both cars have E38 ECM

one is a manuel one is auto but with the auto you choose E38-T43
the manuel you choose just E38
any advice would be great

[restless@westnet.com.au]

any help on this
oztrack said it is a soft ware problem in the new bbx logging update ??

[joecar]

Which V8 build version do you have...?

[restless@westnet.com.au]

the latest one
i reloaded and updated it yesterday still wount work
it will read the pids in pass through as i got steve to set it up
but he couldent get it to bbx log eather if he couldent get it going i have no hope

[joecar]

V8 build 155...?

[restless@westnet.com.au]

Yes build #151
ver 8.2.1

[restless@westnet.com.au]

if i down load build #155
would that fix it ??

[Blacky]

if i down load build #155
would that fix it ??
It may help. Build 155 contains updated firmware for FlashScan V2. That updated firmware (V2.07.11) contains changes to the way BBL starts up. On some E38/T43 combos the logging would not start - that is fixed in the new firmware.

If, after you install the new firmware it still fails, then after it fails save a trace file on the V2 (using options F1->F3->F1), then using EFILive Explorer copy that saved trace file to your PC/laptop and email it to me at paul@efilive.com

Regards
Paul

[restless@westnet.com.au]

this is the answer from pauel

It will be fixed in the next release of the V8 software. The PIDs for that
OS 12639270 hadn’t been defined

when is the next v8 up date ??

[Blacky]

when is the next v8 up date ??

Monday, US time.

Regards
Paul

[restless@westnet.com.au]

ok thanks

[Tordne]

this is the answer from pauel

It will be fixed in the next release of the V8 software. The PIDs for that
OS 12639270 hadn’t been defined

when is the next v8 up date ??

That was from me actually and at that time the next update schedule was unknown :)

[restless@westnet.com.au]

so is this up date out yet ??

[joecar]

V8 build 156 has been posted to the downloads page at www.efilive.com.

[restless@westnet.com.au]

yes put it hasn't FIXED the problem as i have downloaded it
up dated it
up graded the boot block
up graded the firm ware
and down loaded the pid list in to the v2 again
it still works fine in an earlier OS but wont work in the latest one OS 12639270 ???

[Blacky]

The update was scheduled for last Monday but just prior to releasing it we got reports from users that the DVT (Dynamic Vehicle Testing, aka bidirectional controls) were incorrect for some CAN vehicles.
We've been fixing those this week. Hopefully we'll have the update ready early next week.

Regards
Paul

[restless@westnet.com.au]

ok paul i will keep a look out for the release next week

can you tell me IF the new ver will read witch GEAR in the latest e3 hsv M6 car with which HAS gear read out on the center screen( HSV of course )
i know the A6 cars do
thanks bob

[Forbz]

Any news on this problem be resolved yet

[Blacky]

Any news on this problem be resolved yet
If you mean have we added DMA PID support for OS 12639270, then yes that is in the latest release.
Regards
Paul

[restless@westnet.com.au]

when was it released

[Blacky]

ok paul i will keep a look out for the release next week

can you tell me IF the new ver will read witch GEAR in the latest e3 hsv M6 car with which HAS gear read out on the center screen( HSV of course )
i know the A6 cars do
thanks bob

No. It is probable that the data required to display current gear for a manual gear box is broadcast on the CAN bus by the ECM.
EFILive does not read the broadcast data while data logging.

Regards
Paul

[Blacky]

when was it released
June 24, 2011, here:
http://www.efilive.com/index.php?option=com_content&view=article&id=48&Itemid=133

However, I recommend updating the software using:
Start->All Programs->EFILive->V7.5->Tools->Check for New Update
and
Start->All Programs->EFILive->V8->Tools->Check for New Update

Regards
Paul

[restless@westnet.com.au]

ok will try it to morrow
thanks

[restless@westnet.com.au]

all works fine now
do you think the pid TRNR (manuel tranmision states) will work soon
cheers

[Blacky]

all works fine now
do you think the pid TRNR (manuel tranmision states) will work soon
cheers

What is wrong with the PID?
Sorry if its already been explained, I may have simply forgotten.

Regards
Paul

[restless@westnet.com.au]

you said a while ago it was not surported (unknown )
so i havent tryed it again

all so could you tell me were to put a trace file to read it
i have got it on the v2 and in explorer( bottom of the page )but witch part of efilive do you past it in to
to beable to read it
thanks

[Blacky]

See images, one is for V7.5 the other is for V8.

Regards
Paul

[restless@westnet.com.au]

ok ill give it a go cheers

[restless@westnet.com.au]

i have up dated every thing v8/v7.5/and the firmware /boot block to day
now i find that the E38 pid ( gear ) for the a6 just shows a 1 in neutral or unknown
all so says says unknown when its in gear ? on the v2 screen
BUT when you log it
it show which gear OK on play back on the PC screen in scan tool
all the other 34 pids show on the v2 screen OK
any ideas
cheers

[joecar]

Yes, I find the same thing... on V2 the encoded pids (e.g. TRNR, GEAR, TCCMDE, TSTATExx, STATExx) show value Unknown on V2 and show correct value in the V7 scantool.

[restless@westnet.com.au]

ok
i guess it will get looked at on the next up date
cheers

[Blacky]

ok
i guess it will get looked at on the next up date
cheers
Yes.
Regards
Paul