PDA

View Full Version : Help- no readout from LC-1



Cyborg
February 24th, 2012, 11:36 AM
Hey guys, im an EFILive beginner, I have an LS2 E40, just had a mechanic install an LC-1, and I can't get a reading from it at all in the EFILive Scan Tool. I selected all the wideband PIDs and I'm plugged into the Out wire from the LC-1. The LC-1 has power. Any help would be greatly appreciated...

joecar
February 24th, 2012, 01:00 PM
Hi Cyborg, welcome to the forum :cheers:


How is your LC-1 wired...?

Do you have FlashScan V1 or V2...?

Which wideband pids are you using...?

Which V7 software build version (do Help->About)...?

Cyborg
February 25th, 2012, 03:21 AM
Hi Cyborg, welcome to the forum :cheers:

-Thanks!

How is your LC-1 wired...?

-I'm using a serial cable, is that what you are asking? Both the EFILive and Innovate serial cables were female so I connected them with an adapter. Maybe I'll try reversing the adapter just in case it's directional. If it would be helpful I could take a pic of how the other wires are connected under the dash.

Do you have FlashScan V1 or V2...?

-V2

Which wideband pids are you using...?

- DESCRIPTION CAPTION UNITS SYSTEM CH PARAMETER
Y Base Efficiency Numerator 1 - Dyno BEN_DYNO factor WO2-Serial 0 CALC.BEN_DYNO
Y BEN Factor Bank 1, Serial Wideband, LS1 style BEN1 factor WO2-Serial 0 CALC.BEN1
Y BEN Factor Bank 2, Serial Wideband, LS1 style BEN2 factor WO2-Serial 0 CALC.BEN2
Y External Wideband AFR WO2AFR1 AFR WO2-Serial 2 EXT.WO2AFR1
Y External Wideband AFR WO2AFR2 AFR WO2-Serial 2 EXT.WO2AFR2
Y External Wideband EQRatio WO2EQR1 EQRatio WO2-Serial 2 EXT.WO2EQR1
Y External Wideband EQRatio WO2EQR2 EQRatio WO2-Serial 2 EXT.WO2EQR2
Y External Wideband Lambda WO2LAM1 Lambda WO2-Serial 2 EXT.WO2LAM1
Y External Wideband Lambda WO2LAM2 Lambda WO2-Serial 2 EXT.WO2LAM2
Y External Wideband Sensor State WO2ST1 WO2-Serial 2 EXT.WO2ST1
Y External Wideband Sensor State WO2ST2 WO2-Serial 2 EXT.WO2ST2

-Since I really don't know what I'm doing, I just selected all the PIDs under the System drop down box:WO2-Serial

Which V7 software build version (do Help->About)...?

-V7.5.1 (Build 180)

Cyborg
February 25th, 2012, 06:54 AM
I am getting a reading now...I selected the following additional PIDs and now I get a readout: OK DESCRIPTION CAPTION UNITS SYSTEM CH PARAMETER
Y Commanded Air Fuel Ratio AFR :1 Fuel 2 GM.AFR
Y Commanded Air Fuel Ratio B - LS2 AFR_B :1 LS2 1 GM.AFR_B
Y Commanded Equivalence Ratio LAMBDA Lambda Fuel 2 SAE.LAMBDA

Now I have a TPP readout question LOL, but I will post it here: http://forum.efilive.com/showthread.php?17634-Throttle-position-Pid&highlight=throttle+percentage