Cummins high idle enable

[straight6]

I have not been in the loop for awhile. I have not had this since i switched to a manual stock tune (auto to manual trans conversion) and operating system. I cannot see paying the dealer $89 for 4 mins of work. If i post my os can someone send me a clean stock manual tune with this enabled? Or any thought when this feature will be added? Or if not already. Like i said been on other ventures for awile. But winters comin and with the thick oil im running to quiet gear rollover. Its hard to shift when cold and standard idle just doesn't cut it. Thanks for any help.

[easymon]

1404814048dont forget tunning alone wont enable, pin 22 if i remeber has to be grounded to but not sure with you for you had auto trans. prior. Here is stock manual high idle just dont forget to change vin. hope attatment went through.

[straight6]

Thanks so much. Yes i did ground pin 22. Now if i remeber i change vin after i tune? Or before? Can u run through the sequence for me in that again? Ive done it once just been a long time. I appreciate it

[GMPX]

Isn't pin22 the clutch switch input?

[easymon]

pin #22 pto control as for vin change think you can now change in tune tool pull stock file copy high lite copy vin. close file pull my file clear vin and paste then go to top hit file then save as done. or the old way load my file on truck do not start open scan tool on top hit biodiretinal hit change vin follow promps.

[straight6]

11352409 is my operating system although some of my tunes are of the operating system that you sent me. im kind of confused. i know i got a stock manual tune with the sane operating system as mine from rob at ATP. some of my tunes are the 409 and some are the one sent. can i go back and forth? sorry to sound stupid just a little confused. thanks for any help

[easymon]

yes you can if you load my you can go back to 409 i have swapped back and forth trying diff. operating sys.

[straight6]

Whats the difference in the 2? I remeber trying mine on my buddys truck and it kicked up a window stating that the Os was different. But i was just curious.... What about all my tunes that are of different Os's? Do i need to script them all over this stick tune?

[easymon]

there were updates better diagnostics clutch save ,hard start, smoke to many to list general idea .you can try scripting if your tunes are not locked but some of the parameters might have change so tunes might not be same after scripting .

[straight6]

So is the ones you sent the latest? So pretty much there ecm calibrations correct?

[easymon]

Thought read that 1 poped out recenty . yes from what i heard.

[easymon]

thought heard on on forum new1 might be out. Not sure on calib.

[crf450x]

So the high idle can be turned on through my autocal if I request it?? Just had EFI for a week....still A LOT I want to learn and I don't even have a v2. First post btw!!

[easymon]

Yes and no yes if you can get stock file with it turned on already no there is no abillity to turn on with just the v2 or autocal at this time.

[crf450x]

Oh okay....can I use the tune you posted on here for a base stock file then have all my tunes built onto that? The dealer wants like $60 to turn it on.

[easymon]

yes you can just dont forget to change vin before start.

[straight6]

Hey man thanks for the stock file. Works great. Bad thing is i have to rewrite all my tunes. With being a different operating system it wont even allow me to cross view my other tunes. But ill get it worked out unless someone has a 409 operating system for an 06 manual trans truck with high idle enabled. Either way i appreciate it

[06redram]

Hey man thanks for the stock file. Works great. Bad thing is i have to rewrite all my tunes. With being a different operating system it wont even allow me to cross view my other tunes. But ill get it worked out unless someone has a 409 operating system for an 06 manual trans truck with high idle enabled. Either way i appreciate it

I thought the OEM 409 OS was for high idle manual 6 that was posted from easymon?

[straight6]

It was the 602 OS he posted. Trust me i am greatful but would make my life much easier to get a 409 OS to script all my tunes over instead of rewriting from scratch and opening another tune tool and reference and copy and paste every table.

[crf450x]

Alright thanks! Just to be 100% clear that is a stock 2006 6 speed manual file? And I can send that to the guy that does my autocal tuning and he can use it as a base?

[06redram]

Alright thanks! Just to be 100% clear that is a stock 2006 6 speed manual file? And I can send that to the guy that does my autocal tuning and he can use it as a base?

I install this OEM H I tune on my truck. I will be the first to say it works great

[crf450x]

I got my new tune based on that and loaded it to the autocal and when I try to flash I get $0526. How can I fix this????? Please reply asap....need to get it figured out tonight and cancel my appointment and $60 at the dealer tomorrow if I can get this to work....

[easymon]

Alright thanks! Just to be 100% clear that is a stock 2006 6 speed manual file? And I can send that to the guy that does my autocal tuning and he can use it as a base?

This was a fresh dealer flash and had tipm and ecm flash so all is clean it is a 602 file with high idle. You guys are more then welcome glad i could help. Shannon

[crf450x]

How do I change it from 11352602 to 11352409?? 409 is what all my other tunes are on. The vin was changed to mine so it's correct and I'm not sure how to change the other thing. Still new to this. Anybody willing to give some help over the phone??

[easymon]

If i remember right all i did was change vin and load or load then change vin just dont start truck till vin change . Far as i know you 409 file cant be loaded on 602 if you want you 409 back on truck just load it and change vin just no high idle. Thought you were going to 602 not to 409 -409 files not compatible with 602 or maybe i missing you here.

[crf450x]

Can you help me on the phone?? In all honesty I know nothing about this. The file you put up was 602. All the tunes on my autocal are 409. I get that error code when I try to load the high idle tune on my truck. The vin is correct. I have no idea how to make it work.

[easymon]

Not for sure but thought that with autocal you can only put tunes that your tuner sends you this may well be your error #0525 i would call or email anarchy. This is the draw back to the autocal vs the v2

[crf450x]

Well I sent that to my tuner and he edited it for a mileage tune to try out and make sure it works. He changed the vin. But I guess I will have to get a hold of him and find out how to fix this. I may just go to the d@mn dealer tomorrow and have them do it. I'm amazed that smarty can turn this on with no problems but efi can't even do it at all. Thanks for the tune and help.

[easymon]

Ok then.

[06redram]

If i remember right all i did was change vin and load or load then change vin just dont start truck till vin change . Far as i know you 409 file cant be loaded on 602 if you want you 409 back on truck just load it and change vin just no high idle. Thought you were going to 602 not to 409 -409 files not compatible with 602 or maybe i missing you here.

Easymon if I install the 602 Can i go back to the 409 ?

[easymon]

Easymon if I install the 602 Can i go back to the 409 ?

Yes just just load your 409 file but i would read the 602 file you have in truck now that way you dont have to play with vin. when loading again.

[06redram]

Thanks easymon