Help on my first calc vet

[400ss]

Today i tried the calcvet, im using a analog wideband..

Does this pids looks ok? and what about the log file? i will atach the current tune on the truck
when i try to aply the same data filter as the tutorial it deletes al the cells

[joecar]

Can you post your calc_pids.txt file.

Post a screenshot of your filter proprties.

[400ss]

Yeah sure, thank you very much really.

[joecar]

I'll look at it later today.

[400ss]

thank you. i think my wideand readings are rare.. i have an LC1 wide band but i cant use it on serial because the serial input of my efilive is melted, do you know where i can send my efilive to changue the serial input for a newone?

[joecar]

thank you. i think my wideand readings are rare.. i have an LC1 wide band but i cant use it on serial because the serial input of my efilive is melted, do you know where i can send my efilive to changue the serial input for a newone?Where are you located...?

[joecar]

Is your FPR manifold-referenced or un-referenced...?

[400ss]

im not in US right now but i can send it if you tell me where i can send it

[400ss]

i have the fuel pressure regulator on the fuel rail but i dont have the vacuum hose conected to it, i think it is tuned for unreferenced manifold vacuum right?

[joecar]

...

Does this pids looks ok? and what about the log file? i will atach the current tune on the truck
when i try to aply the same data filter as the tutorial it deletes all the cells
Post a screenshot of the whole scantool window showing this.

( I got it to work ok on my PC )

[400ss]

i started on 81 C and hit 102 C in some ocations

[joecar]

i have the fuel pressure regulator on the fuel rail but i dont have the vacuum hose conected to it, i think it is tuned for unreferenced manifold vacuum right?Ok, the IFR in your tune file indicates unreferenced.

[joecar]

i started on 81 C and hit 102 C in some ocationsI was thinking out loud... :)

your logged ECT range is inside your filter's range.

[joecar]

Gut feeling: in your Windows properties, change Locale to US (so you get . as the decimal point), and restart the scantool, bring the map up and apply the filter.

[400ss]

thanks for the help, is normal the AFR going up and down?? it nevers hit the PE comanded fuel, i have it on 11.80-12.10 on PE and the lowest it will go on the logs is like 13.20 ??

Post a screenshot of the whole scantool window showing this.

( I got it to work ok on my PC )

[400ss]

ok let me try it, hope it fixes it..!! thanks

Gut feeling: in your Windows properties, change Locale to US (so you get . as the decimal point), and restart the scantool, bring the map up and apply the filter.

[400ss]

you mean on WINDOWS my pc software ? how do i do that?? dont know how to do it, thank you veryy much

[joecar]

thanks for the help, is normal the AFR going up and down?? it nevers hit the PE comanded fuel, i have it on 11.80-12.10 on PE and the lowest it will go on the logs is like 13.20 ??
Yes, wideband AFR will squiggle a lot.

Using LM Programmer you can set the LC-1 to report 1/6th, that will reduce the squiggles.

Also need to make sure wideband is working right, do rich/lean test (in open air should peg lean, then when you cover with rag lightly sprayed with brake cleaner it should peg rich for 10-20 seconds and then lean again)(there's a youtube video on this).


I see PE enabling... but your B3616 requires a lot of throttle to enable PE...

set B3616 to same as 2002 Camaro 12212156 file (under 65% under 3200 rpm, 35% above 3200 rpm).

[joecar]

you mean on WINDOWS my pc software ? how do i do that?? dont know how to do it, thank you veryy muchhttp://windows.microsoft.com/en-US/windows-vista/Change-the-system-locale

[joecar]

I got the filter to work on my PC:

14423

My filter is different than yours, but yours should still work...

I think the problem may be the decimal point character ( comma vs dot )

[400ss]

-My locale now is US but still cant get the . i tried just the 5% per 100 ms filter and it did remove some cells, but when i use the temp filter it will remove all cells

-i changued B3616 , can you take a look on my VE table, spark table and MAF table, i think my MAF is dialed correctly because i loged it today and it shows 1.0 on almost all cells in some ones it shows 1.1

Why did your MAP on the scantool shows colors on the cells and decimals? and my table dont have color and just one decimal

You really helping me, thank you i apreciate it

[joecar]

-My locale now is US but still cant get the . i tried just the 5% per 100 ms filter and it did remove some cells, but when i use the temp filter it will remove all cells

-i changued B3616 , can you take a look on my VE table, spark table and MAF table, i think my MAF is dialed correctly because i loged it today and it shows 1.0 on almost all cells in some ones it shows 1.1

Why did your MAP on the scantool shows colors on the cells and decimals? and my table dont have color and just one decimal

You really helping me, thank you i apreciate itTry the filter shown in my pic (you have to enter it by hand).

In the map properties: on the Data tab, set Precision to 3 or 4; on the Color tab check mark Colored and Hig Contrast; save the properties.

[joecar]

B3616 is good like that (allows PE to enable easier).

[Blacky]

thank you. i think my wideand readings are rare.. i have an LC1 wide band but i cant use it on serial because the serial input of my efilive is melted, do you know where i can send my efilive to changue the serial input for a newone?

https://www.efilive.com/index.php?option=com_content&view=article&id=49&Itemid=84
Regards
Paul