Error $0311: Mode not supported($11) While trying to read lly tcm

[00f3fiddy]

I am trying to read a lly tcm and keep getting $0311 error. I have disconnected batteries and completely shut down PC. I just recently updated my v7 and 8 software.

Any knowns?

Thanks

[joecar]

Did you also update the V2 firmware and BBx config files...?

[00f3fiddy]

I'm not sure on the BBX stuff. Firmware is 2.07.39

[joecar]

Start V8 S&T, goto BBx, click Read, click Save, click Program All (accessed via downarrow next to Program).

[00f3fiddy]

when I click read I get a Error $1085: File or folder not found.

I have never fooled with BBX before. This was the first time I have ever clicked on it.

[00f3fiddy]

Just tried the old way and got a Script exited with code $0331: Request out of range ($31)

[joecar]

when I click read I get a Error $1085: File or folder not found.

I have never fooled with BBX before. This was the first time I have ever clicked on it.Start V8 S&T, got BBx, on the Scan tab edit the pidlist (delete any that are not for your ECM/TCM), on the Tune tab edit the ECM/TCM list (delete any that are not yours), click Save, do Program All (accessed via downarrow next to Program).

[00f3fiddy]

After doing what you said I got a Acces violation at address 0040b2c4 in module 'EFILive_ScanAndTune.exe'. Read of FFFFFF9

When I click ok to close it it keeps popping back up!

[00f3fiddy]

This is KILLING me. It wont let me close out that window. I have to shut the computer down to close it.

[joecar]

After doing what you said I got a Acces violation at address 0040b2c4 in module 'EFILive_ScanAndTune.exe'. Read of FFFFFF9

When I click ok to close it it keeps popping back up!


This is KILLING me. It wont let me close out that window. I have to shut the computer down to close it.Which V7 and V8 build versions...?

[00f3fiddy]

How can I find my build versions? I am on boot block 2.07.04 and firmware 2.07.39

Thanks

[joecar]

In V7 scantool/tunetool: Help->About

In V8 S&T: see upper right.

[00f3fiddy]

In V7 scantool/tunetool: Help->About

In V8 S&T: see upper right.

V7--- is v7.5.7 build 230

V8--- is 8.2.2 build 224

[joecar]

I notified Tech Support.

[wesam]

Joe I have the same problem with E39 2013 Camaro V6
when i tried to read i noticed an error : Request Out of Range ($31)
Also there is no TCM detected while the car is A6
my build is V7.5 Build 211 V8 Build 203

[joecar]

Joe I have the same problem with E39 2013 Camaro V6
when i tried to read i noticed an error : Request Out of Range ($31)
Also there is no TCM detected while the car is A6
my build is V7.5 Build 211 V8 Build 203Can you try with latest version.

[GMPX]

I am trying to read a lly tcm and keep getting $0311 error. I have disconnected batteries and completely shut down PC. I just recently updated my v7 and 8 software.
Was it working with previous versions? That response sounds like maybe a locked TCM too.


Joe I have the same problem with E39 2013 Camaro V6
when i tried to read i noticed an error : Request Out of Range ($31)
That sounds like the ECM is rebooting before the read begins, it might be an E39A, try updating everything and use the Autodetect function in V8, it'll choose the right E39 type for you.

[wesam]

I used the Auto detect it says it is E39
I was afraid to update to the latest version as I'm working on a lot of cars daily but i will update to the latest version today
I hoop every thing goes without problems

[joecar]

Remember: after you flash the newest firmware into V2, goto V8 S&T BBx and do Format Config Filesys, then do Program All of your pidlists/controllers.

[wesam]

Why should i format the config file and program it again ?
I tried to read scan and write and every thing seems OK !!

[joecar]

To wipe out any old config files, and then Program All will write new config files


(some of the filenames have changed over various versions, the Format will delete all files and the Program All will write the new ones).