CSP5 "Switch FALIED"

[iCTD]

Anytime I try to switch tunes I get a "Switch FAILED" message from the Autocal. The CSP5 file downloads without any issues to my 07 truck, I'm on the latest firm (Nov 5), I followed the instruction to a tee, and have updated all the EFI 7.5 and 8 programs. Any ideas as to why I keep getting this issue?

[GMC-2002-Dmax]

Is your switch one of the Socal Diesel CSP5 switches ?

Or is it from another company ?

[blklmm]

You still having this issue?

[cindy@efilive]

Is your switch one of the Socal Diesel CSP5 switches ?

Or is it from another company ?

Further to Tonys question, what software and firmware versions was your tuner using to create the tunes, and what has your tuner said?

Cheers
Cindy

[blklmm]

I've had this issue on a few trucks now, it worked with the first pre-release but now that I've updated to 2.07.52 (firmware) 2.07.06 (boot block) Software is build 237 (v8)and v7 build 245. I'm using so-cal switches. It'd be nice if there was a way to troubleshoot this a little. I'll have to get a couple trace files to send.

[cindy@efilive]

I've had this issue on a few trucks now, it worked with the first pre-release but now that I've updated to 2.07.52 (firmware) 2.07.06 (boot block) Software is build 237 (v8)and v7 build 245. I'm using so-cal switches. It'd be nice if there was a way to troubleshoot this a little. I'll have to get a couple trace files to send.

The changes between the first pre release and the current release were designed to improve response rates and reduce chatter. What else is on the vehicles you are having trouble with? Are you using the scan tool concurrently and what aftermarket devices are installed?

Cheers
Cindy

[WyoFreeride]

Did you rebuild the CSP tune from scratch with the newest version or are you still using the file created with the pre-release software?

[dslbroscumns]

Any luck with this? I'm having same problem. My CSP5 won't work either. Been working on it with tuner for a while now with no luck.

[cindy@efilive]

What software, firmware and bootblock are you using? Are you switching via FlashScan v2, AutoCal or a 3rd party switch? If a 3rd party switch, have you tried using your EFILive hardware for switching?

[dslbroscumns]

I am using my AutoCal and CSP5 with pass through. I use V8 \firmware 2.07.53 date 11/19/2013\bootblock 2.07.06 date 8/2/2013. I have a feeling it may have to deal with me upgrading to the pre-release software. I'm told I can't go backwards on firmware either.

07 5.9 Cummins

[dslbroscumns]

Also sorry for hijacking the thread iCTD. I had similar issue and hoped to help the thread out.

[cindy@efilive]

I am using my AutoCal and CSP5 with pass through. I use V8 \firmware 2.07.53 date 11/19/2013\bootblock 2.07.06 date 8/2/2013. I have a feeling it may have to deal with me upgrading to the pre-release software. I'm told I can't go backwards on firmware either.

07 5.9 Cummins

You are running the most recent version.....provided your tuner is running those versions too.You cannot write or edit tunes given you have AutoCal that is the function of your tuner and their FlashScan device. Your tuner needs to ensure that their FlashScan software matches the AutoCal software.

The only thing I can think of that could be causing this problem is that your tuner wrote your tune in the original prerelease software for CSP, which is not compatible with later software releases. All CSP tunes needed to be rewritten in our October (or later) release software to maintain compatibility.

When did you first start running CSP? And when did you start having issues?

Cheers
Cindy

[dslbroscumns]

I first received my tunes in October without the CSP5 but with CSP5 tunes so I could still switch. At this time it worked as far as switching with the autocal. I didn't actually get my CSP5 till the beginning of November. around January I had the tuner look at my tunes because my truck had been loping at idle that's when I downloaded the prerelease software before the November 17 release. He sent me a smoothed out tune and I went to put the tune on my AutoCal and EFILIVE explorer wouldn't work after many re downloads of the stable release on the site and reinstall I then found the beta November 19 release on the forum. The Explorer finally worked with that and I could finally put the new tune on my AutoCal. My tuner thinks that since I updated my AutoCal to the beta version and they use the current stable version, it may have something to do with me not being able to switch tunes on my AutoCal. Also my CSP5 switch still does not work. The LEDS do not blink with every corresponding switch number. We have tried 2 different switches as well.

[GMPX]

Can you have your tuner confirm your CSP5 tune is V1.01 ?
See Pages 5 and 6 of this document (http://download.efilive.com/Documentation/Cummins%205p9L%20CSP5%20User%20Guide.pdf):

Cheers,
Ross

[dslbroscumns]

Verified the tune is V1.01

[GMPX]

Ok well the tune is at least the correct version for the switches.
I am not sure on the operation of the LED's on the switch, I don't know what the flashing (or no flashing) would indicate, I'll ask SoCal to take a look at the thread.

[Trippin]

Is there anything else plugged into the OBDII port or tapped into the wiring behind the port, such as remote start, alarm, aftermarket stereo equipment, deluxe super widget?

[dslbroscumns]

Nothing else is plugged in

[dslbroscumns]

Well update with mine. Mike went through and started from scratch on my tune from my original stock file and I just loaded it into the truck and it works just fine now.

[ATPCummins]

I really don't know about this one. The tune was originally created with the same software that I had done many other CSP5 tunes with. I just went back through the normal process again and apparently it worked. Glad it is working for your, Chad.