PDA

View Full Version : Getting Scanner to read Lambda



fxracer20v
March 25th, 2014, 11:49 AM
Hey guys. My brain hurts a little and need help. I have a feeling I am just overlooking something. I want to view my LM-2 as lambda on the scanner. It is going into my Ext.1 and is working properly when I choose WB02-LC11. I just cant seem to figure out the custom PID portion of everything. I want to log in lambda because now that I changed Stoich AFR in the tune to 14.27 for the wonderful E10 we have, now my BEN factor is way off cause commanded AFR is 14.27 which = 1 lambda. I am a fan of tuning with lambda vs AFR.

And then my next question, this system will only show me Commanded EQ or Commanded AFR, no Commanded Lambda. So what do I need to do, or what formula/custom PID do I need to convert either the commanded AFR or the commanded EQ over to lambda so I can use a BEN Factor for tuning.

this is a 05 5.3l

Any help would be greatly appreciated! Thanks Guys

darcy
March 25th, 2014, 02:02 PM
How is your LM-2 hooked up? I presume via serial, since you refer to EXT.

In this case, log Commanded EQRatio (GM.EQRATIO) and Wideband Lambda (EXT.W02LAM1), then use the BEN factor CALC.W02BEN.

joecar
March 25th, 2014, 02:54 PM
See post #1 here: Calc-VET-correcting-MAF-and-calculating-VE-in-single-log (http://forum.efilive.com/showthread.php?15236-Calc-VET-correcting-MAF-and-calculating-VE-%28in-single-log%29)

Also see here:

V2 serial/digital wideband logging:
showthread.php?t=8858 (http://forum.efilive.com/showthread.php?t=8858)
showthread.php?t=8115 (http://forum.efilive.com/showthread.php?t=8115)
showthread.php?t=10251 (http://forum.efilive.com/showthread.php?t=10251) post #2

V2 serial/digital input (LC-1):
showthread.php?t=8115 (http://forum.efilive.com/showthread.php?t=8115)
showthread.php?t=7532 (http://forum.efilive.com/showthread.php?t=7532)
showthread.php?t=8348 (http://forum.efilive.com/showthread.php?t=8348)
showthread.php?t=9340 (http://forum.efilive.com/showthread.php?t=9340) post #3
Getting-some-odd-s-from-my-LC-1-wideband-please-take-a-look-at-my-log (http://forum.efilive.com/showthread.php?22863-Getting-some-odd-s-from-my-LC-1-wideband-please-take-a-look-at-my-log) post #13

V2 serial/digital input (LC-2):
LC-2-Digital-Wideband-anyone-try-it-out (http://forum.efilive.com/showthread.php?23169-LC-2-Digital-Wideband-anyone-try-it-out)

V2 serial/digitial input (LM-2):
Flashscan-to-LM-2-Serial-Cable (http://forum.efilive.com/showthread.php?8737-Flashscan-to-LM-2-Serial-Cable)

V2 serial/digital input (PLX):
showthread.php?t=7726 (http://forum.efilive.com/showthread.php?t=7726&highlight=convert+PLX+serial)

V2 serial/digital input (AEM):
showthread.php?15748-AEM-compatibility (http://forum.efilive.com/showthread.php?15748-AEM-compatibility)
showthread.php?16636-Installing-an-AEM-Wide-Band-02-and-logging-afr (http://forum.efilive.com/showthread.php?16636-Installing-an-AEM-Wide-Band-02-and-logging-afr)
showthread.php?16904-AEM-EUGO-Lambda-W-B-how-to-connect-to-Flashscan-V2 (http://forum.efilive.com/showthread.php?16904-AEM-EUGO-Lambda-W-B-how-to-connect-to-Flashscan-V2&p=151205#post151205)

V2 serial/digital input (Zeitronix):
showthread.php?14743-Strange-AFR-from-Serial-ZT-2-OFF-by-Factor-of-10 (http://forum.efilive.com/showthread.php?14743-Strange-AFR-from-Serial-ZT-2-OFF-by-Factor-of-10)

LC-1 free air calibration from V2:
showthread.php?p=93571#post93571 (http://forum.efilive.com/showthread.php?p=93571#post93571)

joecar
March 25th, 2014, 02:56 PM
Serial comms from wideband would allow you to log in Lambda.

PCM commands in EQR.

Both are independent of stoich AFR.



( to run correctly, you would still need to set B3601 to the stoich of the fuel you're running )