PDA

View Full Version : Eops



CR500
August 10th, 2014, 05:02 AM
Trying to log EOPS. Sent the PID to EFI, connect it to car, start logging and I can see EOPS varying like it should. Save file, shut down, connect to computer, and .... no EOPS?

Any ideas?

Using LS1B_A for a 2000 LS1 Corvette.
EFI V8.2.2.258
Firmware 2.07.64
Boot 2.07.07

Thanks!

joecar
August 10th, 2014, 10:46 AM
Post log file.

CR500
August 10th, 2014, 11:30 AM
I tried EFI 7.5 and it can see EOPS!

Am I doing something wrong with V8 or is another thing thats not quite ready?

Thanks

joecar
August 10th, 2014, 12:31 PM
You have to select the pid CALC.EOPS and then save the log (no need to re-log).

CR500
August 10th, 2014, 12:44 PM
So I go into V8. Select Scan. Open log file, and can't find CALC.EOPS under available PID's.

Actually, why would I need the calc pid (even though I can't find it)? I'm not trying to calculate the pressure, I can't even view the voltage (in V8).

I can view the voltage (EOPS) and calculate the pressure in V7.5.

CR500
August 12th, 2014, 07:48 AM
No one ........

Guess I'll bounce it to the support side.

joecar
August 12th, 2014, 11:15 AM
Sorry, my internet connection has been down for a couple of days...

Calc pids are added in later when viewing the log file.

So can you view EOPS pressure in the V7 scantool...?

So in V8 and V2 BBL you can't see the EOPS voltage pid, is this the crux of the issue...?

CR500
August 12th, 2014, 11:47 AM
Log file was acquired via BBX.
EOPS Voltage can be seen on the V2 while BBX recording.
EOPS Voltage displays fine in V7.
Can't see EOPS voltage pid in V8.

joecar
August 12th, 2014, 12:09 PM
Ok, I pm'd Paul, he said he's looking at it.

CR500
August 12th, 2014, 12:19 PM
Appreciate it!

Blacky
August 12th, 2014, 12:24 PM
Trying to log EOPS. Sent the PID to EFI, connect it to car, start logging and I can see EOPS varying like it should. Save file, shut down, connect to computer, and .... no EOPS?

Any ideas?

Using LS1B_A for a 2000 LS1 Corvette.
EFI V8.2.2.258
Firmware 2.07.64
Boot 2.07.07

Thanks!

After investigating this issue, it is now a confirmed bug. GM.EOPS will not show up in the V8 scan tool. It will be fixed in the next update.

The workaround is to hex-edit the *.efi log file and change the PID name GM.EOPS to XX.EOPS. That will force the V8 software to not try to (incorrectly) rename the PID to GM.EOP which is not a supported PID in V8.
I've attached a fixed version of your log file.

Regards
Paul

CR500
August 12th, 2014, 12:34 PM
Whew, I wasn't doing anything wrong.

Thanks!

Blacky
August 12th, 2014, 12:43 PM
Whew, I wasn't doing anything wrong.

Thanks!

No, I've got the monopoly on that :(
Regards
Paul