PDA

View Full Version : 4l80e tcc throttle close cax



TrendSetter
January 22nd, 2015, 06:18 AM
Hi,
I have seen other threads where Taz mentions having the addresses for the 4l80e tcc lockup tables and was wondering if there is any plan to release a cax for these?
I am building my harness now and would prefer to run the 4l80 wiring but would like the lockup on closed throttle.
I'm using cos5 for the 12212156 os.
Thanks

Lextech
January 22nd, 2015, 06:26 AM
Post your tune when you are ready.

Jeff

DrX
March 29th, 2015, 09:28 AM
I could use this fix as well. My TCC is repeatedly locking/unlocking if cruising at around 20% throttle. TCC tables are basically stock 80E tables.

Lextech
March 29th, 2015, 09:57 AM
Hhmmm, I'm having laptop, .ctz issues. Let me get this sorted out.

Jeff

Lextech
March 29th, 2015, 02:33 PM
Hey Drx. Try this out.

DrX
March 29th, 2015, 02:41 PM
Got it. Thanks.

TrendSetter
August 16th, 2017, 10:36 PM
hi,
could you apply the fix to my tune please?
thanks
21379

joecar
August 17th, 2017, 05:37 AM
hi,
could you apply the fix to my tune please?
thanks
21379Send Lextech a pm and ask him nicely :)

Lextech
August 17th, 2017, 09:54 AM
Hey Dave, (Trendsetter) Here is your altered tune.

Jeff

joecar
August 17th, 2017, 09:54 AM
Jeff, thanks.

TrendSetter
August 17th, 2017, 11:34 AM
got it, Thanks jeff

brentg454
August 30th, 2017, 02:53 PM
Lextech, can you do the same for me please?
Thanks, Brent

Lextech
August 30th, 2017, 10:02 PM
Here you go.

Jeff

brentg454
August 31st, 2017, 06:59 AM
Works like a champ...thanks again Jeff!

joecar
August 31st, 2017, 07:35 AM
+1 thanks Jeff.

PSI
September 14th, 2017, 04:39 PM
Would really appreciate if you could modify my tune Jeff. Its a pain with a high stall triple disk converter locking in and out thanks.

Dil

Lextech
September 14th, 2017, 10:04 PM
Hi Dil,
I don't have the parameters for that Operating System. If you tell me what year it is based on and I can try to see if I can figure it out.

Jeff

Lextech
September 15th, 2017, 10:41 AM
Ok, I looked in the COS tutorial and saw that it is based on the 12579405 Operating System. I added the parameters for that. Here is your calibration.

Jeff

PSI
September 15th, 2017, 11:29 AM
That was quick , thanks Jeff, much appreciated . I must be really dumb or I've had a long day at work, but I cant find the parameters in the uploaded tune . I looked under trans and tcc tables couldnt find anything . Could you please point me in the right direction.

Lextech
September 15th, 2017, 11:37 AM
You won't find the parameters by viewing your calibration. They have been changed but won't appear without the appropriate .cax files installed into your software.

Jeff

LS1FREEK
September 21st, 2017, 12:28 PM
Hey Lextech, Could you upload the cax files for this? If not could you apply this to my tune?

21525

Lextech
September 21st, 2017, 12:35 PM
Hey John,
Here you go.

Jeff

joecar
September 21st, 2017, 03:07 PM
Jeff, thanks.

Tinbender59
November 30th, 2017, 01:30 PM
Jeff is the Man of the hour, sent him mine and got it back the next morning. thanks Jeff

PSI
December 4th, 2017, 07:32 PM
Hey Jeff , you modified my tune a while ago , I still can't get the converter to stay locked when I get off , can you please take a look at it again . Sorry to bother you again

Lextech
December 5th, 2017, 01:30 AM
Hey Jeff , you modified my tune a while ago , I still can't get the converter to stay locked when I get off , can you please take a look at it again . Sorry to bother you again
I lowered the settings a bit. See if this does the trick.
Jeff

nonnieselman
February 6th, 2019, 01:51 AM
I lowered the settings a bit. See if this does the trick.
Jeff

Tried to send it thru a PM.. here ya go..

Lextech
February 6th, 2019, 03:06 AM
Here you go.

Jeff

nonnieselman
February 6th, 2019, 11:37 PM
Here you go.

Jeff

Anything special I need to do? I flashed it In and still unlocking under 5% TPS.

Lextech
February 7th, 2019, 12:53 AM
Hhmmm. Try this. I lowered the MPH a bit.

nonnieselman
February 7th, 2019, 10:41 AM
Hhmmm. Try this. I lowered the MPH a bit.


Same thing. Will a log help?

Tinbender59
February 7th, 2019, 03:46 PM
Hey Jeff , you modified my tune a while ago , I still can't get the converter to stay locked when I get off , can you please take a look at it again . Sorry to bother you again

Just a heads up, my truck kicks the TC out when i let off lightly as in going down an overpass. And when i run over 73mph. The DTC codes says cylinder missfires and cylinder#7 missfires. I have chased everything electronic finally put a stethoscope to it at #7, oh my heavens!!! Ive never heard such a noise from a "good" running motor. Gotta get in there asap. Check your misfires??

joecar
February 9th, 2019, 07:02 AM
...
put a stethoscope to it at #7, oh my heavens!!! Ive never heard such a noise from a "good" running motor. Gotta get in there asap. Check your misfires??

Lifter/valvetrain noise...?

Supercharged111
February 9th, 2019, 07:42 PM
Lifter/valvetrain noise...?

Tinbender is old school, he may have used a stethoscope to come to that conclusion. Pretty sure his motor is stock.

joecar
February 24th, 2019, 06:38 AM
Steth is fine... I'm wondering if it's just valvetrain, or if it's more severe.

Tinbender59
March 9th, 2019, 12:30 PM
Tinbender is old school, he may have used a stethoscope to come to that conclusion. Pretty sure his motor is stock.

sorry i wasn't notified of the responses, yes, I used a Stethoscope, I have had the valve cover off, couldn't see anything obvious. I hope to get the G6 out of the shop tomorrow. (bad fuel tank vent valve, leaking oil sender took out the starter, starter took out the battery "weak anyway") lol Are we having fun yet??? anyway?? The truck is going in for exploratory surgery Monday or Tuesday, worst case - broken piston, not burning oil?? best case - collapsed lifter, probable issue - pitted camshaft. my machinist thinks this is the problem claims to have seen a lot of them lately??, it does sound like a stinking diesel at idle!!! gurrrr I've got $13000 invested, not quitting now.


look at this https://www.youtube.com/watch?v=ux84a6SJAc0

Supercharged111
March 10th, 2019, 06:08 AM
My 454 did that. Got the truck like that and didn't even know it, the belt sqeaks were louder than the ticking. When I was addressing the belt squeak I heard the tick so I just ordered a cam and lifters without opening anything. I was right. I'm not sure that the 8.1 was prone to this as well? If so, you can run a GenVI cam if you get the plate so you're not subject to the terrible aftermarket of 8.1 cams.

Tinbender59
March 11th, 2019, 10:27 AM
Long story short found the rocker arms wore out where the ball sets, making a popping sound when you move the ball. Second Long story short expert wasn't going to tell me that unless I bought his rockers. But he did mention if I put a larger than stock cam in I would wear them out , so I went looking. Also found camshaft had gald marks on it, check the rollers in the lifters, all three that I checked, the roller bearings had rough spots in them. I guess it isa blessing in disguise that I caught it before it destroyed the motor. I'll be Going back stock with everything. my research shows if I put a bigger cam in, I'll have to put in roller rockers, next will be springs, then headers, then??? where does it end. Ill just stay stock, it's a farm truck. Besides $600 repair bill beats $1600+++++??

Tinbender59
March 11th, 2019, 10:32 AM
P. S. Sorry for hijacking your post

joecar
March 12th, 2019, 02:26 PM
Good that you found it now.

Tinbender59
March 12th, 2019, 03:15 PM
Thank you

PSI
July 28th, 2019, 12:05 PM
Just a heads up, my truck kicks the TC out when i let off lightly as in going down an overpass. And when i run over 73mph. The DTC codes says cylinder missfires and cylinder#7 missfires. I have chased everything electronic finally put a stethoscope to it at #7, oh my heavens!!! Ive never heard such a noise from a "good" running motor. Gotta get in there asap. Check your misfires??

I never got around to looking into the issue the project got put on hold , I think it was a ECM issue or the tune file was corrupt because commanded timing kept going to 60 degrees.

PSI
July 28th, 2019, 12:10 PM
Now I have a different project going was wondering if somebody still provides a service to have the tcc locked at 0% tps and also have the ability to hold first gear in manual low and not upshift to 2nd . Would be willing to pay a small fee as well just want to get it sorted . Its a 2000 ECM with 512 kb memory . It just sucks efilive doesn't do anything about it since both features are available on HP tuners. Thanks

1bar
April 8th, 2020, 04:25 PM
Anyway we can get the CAX for this?

nonnieselman
April 9th, 2020, 12:36 AM
Contact Lex Tech and he can help you.
Don't think anybody is gonna hand out a CAX they spent alot of time on.

Sent from my SAMSUNG-SM-G870A using Tapatalk

ddnspider
February 8th, 2023, 02:57 AM
24343
Could someone add these tables to my tune please?