PDA

View Full Version : Serial Wideband Issues after Update


LastCall
May 16th, 2015, 08:54 AM
So I've used the serial connection on and off for a few years on my Lc-1. I recently did an update for the flash scan and scan tool.

Now when I select the Serial PIDs for both AFR and lambda, they come is available. The values also come through on the flash scan display.. However, I can't log them through pass through on the scan tool software. I followed the tutorial and still no luck.

Ideas anyone?
joecar
May 16th, 2015, 11:26 AM
V8 S&T -> Devices -> Logging

did you checkmark "Automatically log all external digital/serial pids"...?
Blacky
May 16th, 2015, 11:28 AM
See Issue #2 here:
https://forum.efilive.com/showthread.php?25502-Known-issues-with-May-01-2015-Public-Release

Regards
Paul
LastCall
May 16th, 2015, 04:01 PM
V8 S&T -> Devices -> Logging

did you checkmark "Automatically log all external digital/serial pids"...?

Yes, I did select it, but that didn't work.


See Issue #2 here:
https://forum.efilive.com/showthread.php?25502-Known-issues-with-May-01-2015-Public-Release

Regards
Paul

I think that may have been the ticket, gonna try again tomorrow or Monday. I downloaded the V7 from the web yesterday, and thought it would be current. But I did not select, check for updates within the scan tool afterwards. I did now, and a patch was downloaded and current with Build 283.

Thanks Paul!
LastCall
May 16th, 2015, 04:07 PM
I did go over the logs from earlier today, and noticed there are values for the W02 serial PIDs. They are just way off from where they should be. See attached log.
Tre-Cool
May 16th, 2015, 10:38 PM
a friend has a similar issue with his new device. I sent it my calibration data for pid list and it was good after that.
joecar
May 16th, 2015, 10:59 PM
I did go over the logs from earlier today, and noticed there are values for the W02 serial PIDs. They are just way off from where they should be. See attached log.
Which wideband do you have...?

Did you configure V2 BBL for this wideband...?

Can you capture a new log.
LastCall
May 17th, 2015, 08:29 AM
a friend has a similar issue with his new device. I sent it my calibration data for pid list and it was good after that.

What changes did you make? I was using the serial PID that EFIlive included with the scan tool.


Which wideband do you have...?

Did you configure V2 BBL for this wideband...?

Can you capture a new log.
I have an LC-1. Yes, I did and it worked fine for a few years. Everything changed with the 7.5 and firmware updates. I did verify that the settings were correct in the V2 box. And I was getting the same values on the V2 box as my gauge. For some reason, it just wasn't making it's way into the scan tool.

Yes, I'll do a new log.
Tre-Cool
May 19th, 2015, 12:04 AM
the problem with the data not coming through the software was actually something to do with the v2 unit data loaded.

even though it was showing on the v2 unit itself correctly.
joecar
May 19th, 2015, 02:07 PM
See this:


See Issue #2 here:
https://forum.efilive.com/showthread.php?25502-Known-issues-with-May-01-2015-Public-Release

Regards
Paul
LastCall
May 21st, 2015, 07:10 PM
The update fixed the issue. Thank you Paul!
kidturbo
July 2nd, 2015, 05:00 PM
See Issue #2 here:
https://forum.efilive.com/showthread.php?25502-Known-issues-with-May-01-2015-Public-Release

Regards
Paul

Thanks Paul.

This one also had me hung up too for past 48hrs. My new Innovate MTX-L serial WO2 displayed fine on the V2 and in BBX, but couldn't for the life of me get any data in Scan V7.5..

Is this issue fixed in the June 2 2015 285 release?
Blacky
July 4th, 2015, 01:28 PM
Thanks Paul.

This one also had me hung up too for past 48hrs. My new Innovate MTX-L serial WO2 displayed fine on the V2 and in BBX, but couldn't for the life of me get any data in Scan V7.5..

Is this issue fixed in the June 2 2015 285 release?

Yes.
Regards
Paul