Need help asap after update!!!!!!!!

[kylelavergne]

just updated all software & firmware for efi live & my V2. tried retuning my truck & my v2 can not access my ecm. I literally retuned the truck perfectly fine yesterday before all the updates. I get error codes $0101 & $0333. tried uninstalling all software & re downloading it. same problem. tried alt keys & assum lock faulty & still same problem. can someone please help!!!!!!!!!!

[Blacky]

This may apply to your situation:

After updating from our downloads page you will have build 276. That build has a known issue with LS1B and E54 (LB7) controllers where it may leave the controller "locked" with an invalid seed/key combination of $0000/$0000. Subsequent attempts to read or flash the controller will return error $0333. See known issue #6 here: https://forum.efilive.com/showthread.php?25502-Known-issues-with-May-01-2015-Public-Release

If you have not already done so, please update to the latest pre-release available here: https://forum.efilive.com/showthread.php?25628-June-02-2015-EFILive-Public-Pre-Release

To restore the correct seed/key in your PCM, use the V7 Unlock ECM option to unlock your controller, specifying $0000 for the unlock key and with the "Try Alt Keys" chekcbox checked.

Regards
Paul

[kylelavergne]

i'm still getting error code $0101. wont even let me attempt to unlock the ecm


This may apply to your situation:

After updating from our downloads page you will have build 276. That build has a known issue with LS1B and E54 (LB7) controllers where it may leave the controller "locked" with an invalid seed/key combination of $0000/$0000. Subsequent attempts to read or flash the controller will return error $0333. See known issue #6 here: https://forum.efilive.com/showthread.php?25502-Known-issues-with-May-01-2015-Public-Release

If you have not already done so, please update to the latest pre-release available here: https://forum.efilive.com/showthread.php?25628-June-02-2015-EFILive-Public-Pre-Release

To restore the correct seed/key in your PCM, use the V7 Unlock ECM option to unlock your controller, specifying $0000 for the unlock key and with the "Try Alt Keys" chekcbox checked.

Regards
Paul

[Blacky]

i'm still getting error code $0101. wont even let me attempt to unlock the ecm

The problem may not be the one I described. What controller are you attempting to read/flash?

Can you try reading it using the V8 software. After it fails, locate the *.htx trace file in the folder \My Documents\EFILive\V8\Trace and send it to me at paul@efilive.com.
Include a link to this thread so I know what its about.

Regards
Paul

[kylelavergne]

I just emailed you paul. please get back to me asap! thanks!

The problem may not be the one I described. What controller are you attempting to read/flash?

Can you try reading it using the V8 software. After it fails, locate the *.htx trace file in the folder \My Documents\EFILive\V8\Trace and send it to me at paul@efilive.com.
Include a link to this thread so I know what its about.

Regards
Paul

[Blacky]

I just emailed you paul. please get back to me asap! thanks!

The trace file shows that the LS1 controller is not responding to any commands from FlashScan. Either the PCM, the loom/connector/plugs/cable or FlashScan is faulty. Sorry I can't be more specific but the trace simply shows no response from the PCM.
Does the engine start/run using that PCM?

Regards
Paul

P.S. Sorry for the delay, I've been out of the office for a couple of days.