Logging AEM wideband issues

[thetruck454]

So I've realized my stregnth is with turning a wrench and not tuning. Black Bear is doing my tuning but I'm trying to get logs for him. I have my calc_pids set up for my wideband
as follows

# ================================================== ============================
# Units
# -------------------
# See sae_generic.txt for more information on the *UNITS section

*UNITS

#Code System Abbr Description
#-------- ---------- -------- -------------------------------------------------------------
AFR1 NONE AFR "Air fuel Ratio"



# ================================================== ============================
# Add slot definitions here
# --------------------------------
# See sae_generic.txt for more information on "SLOT" formats
#
#Units Low High Fmt Expression
#------------ ------------- ------------- ---- --------------------------------------------------------------
*CLC-00-0018
V 0.0 5.0 .1 "{EXT.AD1}"
AFR1 8.0 20.0 .1 "({EXT.AD1}*2.375)+7.3125)"

# ================================================== ============================
*PRN - Parameter Reference Numbers
# --------------------------------
# See sae_generic.txt for more information on the *PRN section
#
#Code PRN SLOT Units System Description
#------------------------- ---- ------------ ---------------- ---------------- ------------------------------------------

CALC.AFR_AEM F018 CLC-00-018 AFR 02-wide "AEM Wideband - Input 1"

In v7.5 scan I can see it under Pids (f8) and select it, but under data(f9) it still doen't show up. Justin gave me a .pid file to log with and I added that calc pid as follows, but it still doesn't work. I have verified by looking at the analog inputs on the V2 I can see the voltage moving around under AD1. Any advise or help?

[Parameters]
CALC_AFR_AEM=1,-1
CALC.FPS=1,-1
CALC.INJPWDC1=1,-1
CALC.POWER_RW=1,-1
GM.APP=1,-1
GM.ETCTP=1,-1
GM.HO2S11=1,-1
GM.HO2S21=1,-1
GM.INJPWB1=1,-1
GM.KR=1,-1
GM.MAFFREQ2=1,-1
GM.TRQDES=1,9311
GM.TRQTRANS=1,-1
SAE.ECT=1,-1
SAE.IAT=1,-1
SAE.LONGFT1=1,-1
SAE.LONGFT2=1,-1
SAE.MAF=1,-1
SAE.MAP=1,-1
SAE.RPM=1,-1
SAE.SPARKADV=1,-1
SAE.VSS=1,-1

[joecar]

Try this:



# ================================================== ============================
# Units
# -------------------
# See sae_generic.txt for more information on the *UNITS section

*UNITS

#Code System Abbr Description
#-------- ---------- -------- -------------------------------------------------------------
None None "" "No units"


# ================================================== ============================
# Add slot definitions here
# --------------------------------
# See sae_generic.txt for more information on "SLOT" formats
#
#Units Low High Fmt Expression
#------------ ------------- ------------- ---- --------------------------------------------------------------
*CLC-00-018
AFR 8.0 20.0 .3 "({EXT.AD1}*2.375)+7.3125)"


# ================================================== ============================
*PRN - Parameter Reference Numbers
# --------------------------------
# See sae_generic.txt for more information on the *PRN section
#
#Code PRN SLOT Units System Description
#------------------------- ---- ------------ ---------------- ----------------------------------------------------------
CALC.AFR_AEM F018 CLC-00-018 AFR 02-wide "AEM Wideband - Input 1"


# place at least 2 blank lines after this one (hit RETURN twice):

[joecar]

When you select it, does it have a red X thru it...?

You also have to select EXT.AD1.

[thetruck454]

It does not have a red x through it, but Ii did not select ext.ad1. Let me try that updated calc_pid and also select ext.ad1

[thetruck454]

I'm able to log AD1 just fine when I added it, I updaded my calc_pid to what you posted and my wideband pid still won't show up under f9 data, yet I can select it and there is no red x under f8 pid.

[joecar]

On the Data tab, click twice on the Heading of the first column...

then post screenshot of the PIDs tab and the Data tab.

[thetruck454]

19628
19629
What is weird is the PID shows a different name than what I used in the calc_pid file.



I ended up openeing the sae_generic file and changing the scaling of one of the preprogrammed WB02's in there to match what i needed. I am able to log that so the end result is what i wanted, just still curious why i couldn't add another.

[joecar]

Weird...

in the screenshot, I don't see EXT.AD1 selected on the PIDs tab (and I don't see it on the Data tab).

[joecar]

Weird...

in the screenshot, I don't see EXT.AD1 selected on the PIDs tab (and I don't see it on the Data tab).


What V7 build version are you running (Help->About)...?

[joecar]

Ok, it looks like your calc_pids.txt file (which I edited and pasted above) is missing some heading stuff...

see attached...


( it is better to attach the calc_pids.txt file rather than to paste its contents )


( should not have to edit sae_generic.txt... if calc_pid.txt is not working then it is incorrect )