E38 Help...

[BRZILLA]

Hey Guys. I have a 2013 Subaru BRZ that I've swapped with an LSA, TR6060, and an E38 ECU. I attempted to start it yesterday for the first time without any success. It does not appear to be firing the fuel inhjectors. I have a noid light connected to the number 2 injector. It will briefly flash until the car sputters and then it quits flashing. If I use starting fluid, I can get it to run as long as I keep spraying starting fluid. Since it's just the fuel injectors that are not firing, I am thinking that it's a VATS related problem. I've veriefied that injectors have power during key on as well as during cranking and start. I've applied the patch, disabled the starter relay, etc. I can't really see anything that I've missed. I've attached my tune file if anyone has any insight, I would greatly appreciate it.


20037


Thanks!

https://5alddg-dm2305.files.1drv.com/y3mQ4rt30sBh9DwnmhPy0zY3xg668F1jQIcSgdcksU8X0uCYd0 58Iz39th6jAtqU36AgG092vbu8y5Dt4CS7M1T97WX_95gvFq2h I7qMctLLB1cCf5MRS-3bqsK_XuX6BJQI17BhSRDrKmTcHLBNbOnrO5vdVqHMsht-HijCzqWOtU?width=4032&height=3024&cropmode=none


https://rxnmmw-dm2305.files.1drv.com/y3my2apF9XMdBb4--9tsvojZ7G6FYuuQACWxIgO-d8-i5btMpgGDeSdefAZO7DR4LIa4pojYB5r27EQfWiQ8eyjDqcroL eo3nj_Z-lBnUn06k6D3X56RBRRYZX7ZB29BTwQo8lpjWAZo8I99-TdXbTDE58PxlxAgnkWvQjDPLp-2zM?width=3024&height=3024&cropmode=none

[joecar]

There's more to it than just applying the patch... you have to play with the VATS parameters...


more info:

E38-E67-VATS-disable-guide-post#119 (https://forum.efilive.com/showthread.php?13210-E38-E67-VATS-disable-guide&p=230339&viewfull=1#post230339)


We also had to set the VATS parameters as follows:



{G1204} VATS Enable No
{G1205} VATS Auto learn Enable Yes
{G1206} VATS Required To Run No
{G1208} VATS Fail Diagnostic Disabled
{G1209} VATS Mode No
{G1210} VATS Type Type 3
{G1211} Remote Start Allowed Yes
{G1214} Relearn Count 1.000000 Counts
{G1215} Relearn Timer 1.000000 Seconds
{G1216} Theft Relearn Password Yes

[BRZILLA]

There's more to it than just applying the patch... you have to play with the VATS parameters...


more info:

E38-E67-VATS-disable-guide-post#119 (https://forum.efilive.com/showthread.php?13210-E38-E67-VATS-disable-guide&p=230339&viewfull=1#post230339)

I was able to figure out my problem. The person who sent me the tune file had put a KPA value in a spot that was looking for a PSI value. The MAP scaler is 312.50 and the offset is -11.25. Instead of -11.25 he had -77.5625 which is the KPA equivalent of -11.25 psi. So where I thought the vats was enabled therefore disabling fuel, I was mistaken. Next problem is figuring out why the cooling fans appear to operate all of the time...

[gmh308]

Hey Guys. I have a 2013 Subaru BRZ that I've swapped with an LSA, TR6060, and an E38 ECU.

That's a cool transplant. Should haul along real nice! :rockon:

[joecar]

+1 it is cool :cheers: