View Full Version : turn on readiness monitors
akafred
April 28th, 2018, 09:30 AM
i have a 06 6.0 in my jeep, i have obd2 testing. i have a working tune but all the readiness monitors seem to be set to not available.
does anyone know exactly what Engine DTC Processing Enablers control witch readiness monitors?
https://docs.google.com/spreadsheets/d/1fw3iH65_M8FYZU6PsxhITcY76_0CKsQygjQAa42fjH0/edit?usp=sharing
22053
1FastBrick
April 28th, 2018, 04:04 PM
Can you post the tune file?
Or at least let us know what calibration you are working with?
akafred
April 29th, 2018, 12:55 AM
Can you post the tune file?
Or at least let us know what calibration you are working with?
22054
akafred
April 30th, 2018, 02:43 AM
does anyone know? need to send this in for etest, i guess i could try wit them all turned off, but i assume they will expect some of the monitors to be on.
joecar
April 30th, 2018, 03:03 AM
I looked at your .ctz and it seems to me that some of the readiness tests should be available...
what vehicle did your 12593058 file come from...?
can you start with a stock 12593058 file and copy your tables over...?
akafred
April 30th, 2018, 03:13 AM
i got the stock file off one of the efilive tuners because it was difficult to find a lq4 + nv4500 manual file online. when i got it i noticed it wasn't a factory flash as a lot of the Engine DTC Processing Enablers were turned off that would be on in a factory dump
i guess i could use a lq4 + 4l80e stock file and try to change it over to nv4500
the engine is from a van/ the harness is home built, i added in the tac wiring as i wanted to be able to have cruise, the trans is from a 2500 manual truck.
may be best to find the latest os that supports my tac.
1FastBrick
May 1st, 2018, 01:14 PM
i got the stock file off one of the efilive tuners because it was difficult to find a lq4 + nv4500 manual file online. when i got it i noticed it wasn't a factory flash as a lot of the Engine DTC Processing Enablers were turned off that would be on in a factory dump
i guess i could use a lq4 + 4l80e stock file and try to change it over to nv4500
the engine is from a van/ the harness is home built, i added in the tac wiring as i wanted to be able to have cruise, the trans is from a 2500 manual truck.
may be best to find the latest os that supports my tac.
I am not sure what that file came from originally with out an original vin.
I do happen to have 2 stock 2004 6.0L with Manual Transmission files you may be able to use assuming your emissions equipment is in tact.
1FastBrick
May 1st, 2018, 01:32 PM
I just thought of something else.
I am not sure what Pedal and tach module you have. If it's an all plastic pedal thats 06,07 classic and will not work with an 03-05 calibration. The 03-05 are metal with a plastic foot pad.
Irreversal
June 2nd, 2018, 09:50 PM
anyone figure this out, in terms of adding readiness monitors? I need to enable EGR.
I might have to reflash it too a 2000 camaro or something else with it built in I think.
akafred
June 3rd, 2018, 02:14 AM
Sent u a email
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.