Stock GEN IV Files

[Black02SS]

If you guys would, please send your stock GEN IV files as well as a description to either Tordne or myself so they can be added to the list.

www.holdencrazy.com (http://www.holdencrazy.com)

Thanks

[02Z06]

Does anybody know if the 06-C6-LS2 is currently supported with V2?


Thanks, Jim

[Black02SS]

It depends on what controller is in the vehicle. If you want to post your vin I would be happy to check it out for you.

[02Z06]

Thanks for the reply Black 02SS. I don't know the Vin of the car as I have not seen it yet. So does the 06 model year C6 LS2 use both the E-40 and E-38 Controller? This is an LS2 not LS7.


Thanks, Jim

[jrh]

All 2006 model year Corvettes (Z06 or base car with the LS2) use the E38 so if your VIN has a 6 in the 10th digit (or a 7 for the 2007 cars), the current release of EFILive will not reprogram them. The 2005 Corvette uses the E40. It was not a mid year model change. The 2005 Corvette uses a different crankshaft reluctor (24x wheel versus 58x wheel on the 2006-2007). You can not mix the engines and controllers/software. The 2006 engine won't run in a 2005 Corvette and the 2005 won't run in a 2006 Corvette.

To confuse things a bit, the 2006 LS2 in the Trailblazer SS, SSR and GTO still has the 24x crankshaft reluctor wheel (and the 2x cam sensor wheel versus the 4x wheel on the newer engines). These vehicles (2006 Trailblazer SS, SSR and GTO) use the E40 ECM like the 2005 Corvette did. EFIlive should support these vehicles because they use the E40 computer.

The crankshaft speed sensors are different for the two different reluctors and they are color coded so you can also tell by the color if it is a 58x sensor or a 24x sensor.

Jason

[Bob's Garage]

Can you please tell me if the following LS2 controller is supported?

VIN
1G1YY24U955100573

Thanks....

[eboggs_jkvl]

I've sent a copy of a stock 2007 LS2 MZ6 Corvette but I don't see it on the list. Did you NOT get it?

I also tried to attach it to this post and it doesn't show.

Would ya'll mind increasing the size of the "tun" files in here as attachments? My 1 meg file won't fit from my 2007 Corvette tune.



Elmer

[Bob's Garage]

Elemer
No I did'nt get it.
Could you please send a copy to robrizok@aol.com

Completely stock, yes?

Thanks in advance

Bob

[eboggs_jkvl]

If you guys would, please send your stock GEN IV files as well as a description to either Tordne or myself so they can be added to the list.

www.holdencrazy.com (http://www.holdencrazy.com)

Thanks

Tordne has his e-mail turned off in his profile.


I transmitted to you and I used tordne@holdencrazy.com (http://forum.efilive.com/member.php?find=lastposter&t=4922#) that for tordne. I hope one of you gets the file. Let me know.

Elmer

[Tordne]

Got it thanks mate :)

I've forwarded it on as it is an E38/E67 unrecognized PCM which we need to produce a cal for.

[jrh]

Can you please tell me if the following LS2 controller is supported?

VIN
1G1YY24U955100573

Thanks....
Based on the fact that 10th digit of the VIN 1G1YY24U955100573 is a 5, that is a 2005 vehicle and from the 1G1YY part, it is a Corvette so that can only be an E40 based vehicle (as I mentioned before, ALL 2005 model year Corvettes are E40). That means the current release of EFILive will support that vehicle. The current operating system for that VIN is 12613186 and that operating system is supported by EFILive (as is the one prior to it for that vehicle).


Jason

[Bob's Garage]

I am still having a problem viewing the operating system. I get the "unrecognised pcm" message.
In the calibration tab the OS is 12595751
I saved a copy of the tune and sent it to support@efilive

For anyone interested I can snd them the file to see if you can read it.
Just sent me your email and I will send the file.

email me at dutchesscamaro@aol.com
I would greatly appreciate someone looking at the file.

Thanks inadvance.

Bob

[Tordne]

There is nothing "wrong" with your file that anyone can "fix". It is just a case of the calibration file not existing for the specific Operating System and therefore not knowing what the data relates to our how to present it (in the form of tabkes etc).

There are heaps of calibrations being created currently for the new E38/E67 and other controlers for which read support was released recently.

The calibrations are due out fairly shortly.

[jrh]

The vehicle he is talking about is a 2005 so it is an E40, not and E38 or E67, so it should already be supported.

Jason

[jrh]

Per the GM TIS web site, that VIN should have one of the two following operating systems:

VIN:1G1YY24U955100573
Controller:PCM/VCM
Powertrain/Vehicle Control Module Calibration History for: Main Operating System
Part Number

12613186
12605740Both of those operating systems are supported by the current EFILive software.

I am not sure why your vehicle is showing 12595751 as an operating system. Are you sure you are looking at the correct file tab because that part number is the speedometer calibration file part number for your vehicle. Are you using the latest EFILive software that supports E40?

If you are still having these issues I would get your vehicle flashed by a dealer to the latest stock calibration files and that should give you the correct operating system (or you can do it yourself if you have the software/hardware to do so).

If you had a stock EFILive calibration with ALL the correct files for that vehicle, you could also use EFILive to update the vehicle.

BTW - anyone can check what the correct files are for a specific VIN GM vehicle by going to:

http://tis2web.service.gm.com/tis2web



Jason

[Bob's Garage]

Jason
You are correct however, for this EARLY pcm OS, 12595692 EFILive does not yet have a cal file.
Ross is working on as we speak to help here.
PLease check your E40 cal file folder to see if you have a ...692 cal file.

I am working with Brent at EPP. He ma be contacting you today on this.
I sent him my stock tune.

Thanks
Bob

[jrh]

Bob,

Just update the ECM to the latest files and this won't be an issue anymore.

Jason

[1meangto]

I just sent you a stock 05 gto a4 program and a stock 06 6 speed program.

[GMPX]

12595692 should be in the current release download FYI.

Cheers,
Ross

[1meangto]

If you guys would, please send your stock GEN IV files as well as a description to either Tordne or myself so they can be added to the list.

www.holdencrazy.com (http://www.holdencrazy.com)

Thanks
did you get the files I had sent you?

[Black02SS]

Yes and I have since forwarded them to Tordne.

[GMPX]

Guy's, I'm not sure Andrew is going to have time to get these up any time soon. Anyone else care to start up something?

Cheers,
Ross

[redhardsupra]

what kind of duties would that involve? i have maintained windows/unix servers for 5yrs, a lot of it was web stuff.

[Tordne]

Guy's, I'm not sure Andrew is going to have time to get these up any time soon. Anyone else care to start up something?

Cheers,
Ross

Damn all the new vehicle support. The list I have is getting a bit big to be useful without adding all the E38 and E67 stuff, let alone the distinction between PCM/TCM.

I think it needs to be grouped somehow which will require database modification and coding. I'm actually thinking maybe something like just a file management system or something. That wold probably be less complex that what I'd naturally want to do.

I'm uploading a few now in any case :frown:

[ringram]

How about file browsing to a file system with tunes put in folders per family (ie) Chevrolet, then by ECM/TCM and the filename describing the tune nicely.
Should be nice and easy to manage and traverse. No database required then and others can help you maintain it.

Should also be possible down the line to make a database with metadata linking to the files if you want to shine it up a tad. Both methods of access can be maintained.

My 2p

I think Tordne is busy with his new spawned offsping and job, he is saving for a massive displacement engine so needs to work all hours of the day :) (At least I hope he is saving for the engine)

[Tordne]

I think Tordne is busy with his new spawned offsping and job, he is saving for a massive displacement engine so needs to work all hours of the day :) (At least I hope he is saving for the engine)

:muahaha:. That would be nice, but first it looks like a swing a slide set for the little one. I got the suspension, clutch and intake done so I should be thankful for that I guess :bash:

[1meangto]

I sent ross a e38 file for a 07 denali the other day he should have it or I can send it to you. Thanks for getting all those files up!!

[VortechC5]

Are you guys still looking for files? If you need them I have the stock PCM and TCM files from my 08 Silverado L76 (with AFM and VVT).

[redhardsupra]

sounds fun, post it up ;)

[nycblazer]

Are you guys still looking for files? If you need them I have the stock PCM and TCM files from my 08 Silverado L76 (with AFM and VVT).
yeah post it up lets see it i need one too:wave:

[VortechC5]

Oops, I forgot to send the files to Tordne. Sorry for the delay.

I just sent them to him to be added to Holden Crazy.

[CarbConn]

We did a LS3. EFIlive does not recognize this LS9 auto Camaro.

Thanks.

Alex

[joecar]

We did a LS3. EFIlive does not recognize this LS9 auto Camaro.

Thanks.

AlexHi Alex, what are your V7.5/V8.1 software build numbers...?

[Tordne]

That calibration you sent via email is supported with the latest pre-release version 7.5.6 Build 107 available here (http://forum.efilive.com/showthread.php?t=13140).

Also download the 8.1.2. Build 87 release and update firmware to 2.06.28. Also get the ZIP file in post # & of that thread and extract to the location shown in that post.

[joecar]

That calibration you sent via email is supported with the latest pre-release version 7.5.6 Build 107 available here (http://forum.efilive.com/showthread.php?t=13140).

Also download the 8.1.2. Build 87 release and update firmware to 2.06.28. Also get the ZIP file in post # & of that thread and extract to the location shown in that post.Yes get the zip file from post #7: http://forum.efilive.com/showpost.php?p=116240&postcount=7

[CarbConn]

Thanks guys, it worked!

[bfabiano]

can you tell me if this controller is supported. 2006 C6 Auto trans vin#********

[Tordne]

I can advise that the E38 T43 controllers used by that VIN (which I've removed) are supported by FlashScan V2 Scan and Tune.

[joecar]

can you tell me if this controller is supported. 2006 C6 Auto trans vin#********


That VIN has had the following OS updates:
12600132 - not supported by EFILive (Main Operating System)
12601696 - not supported by EFILive (New software for start of production)
12602922 - supported by EFILive (New software to correct problem occurring at the assembly plant. Does not address any service issues.)
12605196 - not supported by EFILive (New software to eliminate erroneous "Max speed 158 mph" DIC message.)
12605732 - supported by EFILive (New software to ensure proper catalyst monitoring.)
12614682 - supported by EFILive (New software contains diagnostics enhancement for DTC P0128 and DTC P0507. Also addresses battery drain.)

If he has one of the non-supported OS, he should be able to upgrade any non-supported OS to the latest OS.
Plus, any dealer should upgrade his ECM to 12614682 whenever it goes in for a service.
...
bfabiano,

EFILive supports the vehicle you enquired about (VIN provided by you).

However, you may have to upgrade to a supported OS... the latest one is 12614682.

Goto http://tis2web.service.gm.com/tis2web and enter your VIN, select PCM/VCM and click Next...
you will see what the dealer will upgrade your OS/calibrations to (the latest one is at the top, 12614682).

[odd boy]

Per the GM TIS web site, that VIN should have one of the two following operating systems:

VIN:1G1YY24U955100573
Controller:PCM/VCM
Powertrain/Vehicle Control Module Calibration History for: Main Operating System
Part Number

12613186
12605740Both of those operating systems are supported by the current EFILive software.

I am not sure why your vehicle is showing 12595751 as an operating system. Are you sure you are looking at the correct file tab because that part number is the speedometer calibration file part number for your vehicle. Are you using the latest EFILive software that supports E40?

If you are still having these issues I would get your vehicle flashed by a dealer to the latest stock calibration files and that should give you the correct operating system (or you can do it yourself if you have the software/hardware to do so).

If you had a stock EFILive calibration with ALL the correct files for that vehicle, you could also use EFILive to update the vehicle.

BTW - anyone can check what the correct files are for a specific VIN GM vehicle by going to:

http://tis2web.service.gm.com/tis2web



Jason

good info

[Sid447]

A 2009 Escalade ECM & T43 TCM,

Along with a 2009 CR8 LS3 ECM & T43 TCM,
........plus a 2009 CR8 M6 ECM sent a couple of weeks ago.
Did you receive them okay?

[Tordne]

Yeah I've gotten them :). My laptop took a dump so I've had to reload everything from scratch again. I'll try and get them uploaded in the next couple of days. Had to search for what the heck a CSV-R8 wal LOL.

[stigmundfreud]

Hi Tordne or anyone else, looking for a stock tune for an LS3 VXR8 (not sure the model name over in Aus) -

O/S 12624402
Cal: 12624488
Transmission: Manual 6 speed.

If anyone has a stock copy can they let me know? There is one tune on holdencrazy with the correct O/S but thats for a different market and also an auto.

Cheers in advance

[Tordne]

Everything I've got is up on Holden Crazy already sorry. If you do come across one please sent it to me and I'll host it.

[stigmundfreud]

Will do, if I could find out the like for like model on the HSV front it would probably be easy. Everyone I know here has had their cars mapped and I've lost my original stock :'(

[Sid447]

Hi Guys,

I sent Tordne a file for a 2009 CSV-R8 M6, OS12628990. I can personally confirm that this is a 100% stock, untouched LS3 M6 file. The 2009 CSV-R8 A6 files also came from me and they are also 100% untouched.

The CSV-R8 (Chevrolet Special Vehicle [sic] ) is the re-badged and not re-engineered version of the HSV Clubsport R8 and also the VXR.

I am 99.9% certain all Australian-built MY2009 LS3 M6's have the same tune file parameters -that includes the 2009 HSV Maloo M6 too; as there's a copy of one there on holdencrazy also, along with an 09 GTS. Though I can't vouch for the originality of those particular files.
With a bit of patience and time you could load the 2009 GTS (which is A6) and the Maloo M6 (same OS numbers) to see a list of the differences for the manual ECM and then do the same for yourself with the CSV-R8 A6 sharing the same OS you have. Enabling you to then make yourself a stock M6 file from the A6.

Or just copy and paste all the parameters over from the CSV-R8 M6 (One of the frustrations of EFI-L; not being able to load different OS's together!)

Or simply flash the file with the different OS into your car if needs be. :cheers:

[stigmundfreud]

Cheers! If you happend to have the m6 available that would be great as I couldnt see it on Tordne's site. There might be some differences due to regional changes as I noticed a lot more other than just the typical auto box when looking at my slightly own modified tune but it would be a good start!

[Sid447]

Hi Stig,

Just scroll down the Holdencrazy stock files list and look right under the 09 Corvette ZR1 file, there are then three files listed for 2009 CSV-R8, you need the last one; OS12628990.
I double checked it last night with the original and it's as you need it, 100% stock.

I believe all the 2009 HSV VE cars had the same file (VXR-8, CSV-R8, Clubsport R8, GTS & the Maloo) though would stand to be corrected.

One person who is good to check with is "GMH308" on here. :cheers:

[endlink]

I am looking for a stock 2006 TBSS e40 pcm file. I found one on holden but the OS # doesn't match up and is off by one number. How or why would this be? Maybe a typo? I would like to start from scratch but know that the OS needs to be the same. Help is much appreciated.

[Tordne]

Often the Os and calibration ID numbers are of by 1 so just maybe double check. It won't be a typo as it wouldn't find a match for the OS in the database ;)

[endlink]

OK, so its normal to be off by one. Was just making sure. It wouldn't make sense to have a two different OS#'s for the same PCM on the same year, make, model vehicle.

[Boost]

So, which ones do you still need? I have many, but I figured most were already commonly floating around and supported.

[endlink]

So my current tune on the truck has an OS # of 02606494 and the holden crazy tbss stock tune has a OS# of 12606494. They are both E40 PCM. If I start from scratch with the holden crazy stock tune I wont have any problems will I? Thanks for the help all.

[wells]

OS question. I have an 09 sierra 4.8l ly2, e38 and t42. I have looked at some of the other tunes on this forum, and I don't have the option of some of the parameters seen using same controllers. I'm assuming this is due to different OS. Being done controllers can I just download said OS and perform tune and download with operating system? Sorry for the nooby question. Awesome wealth of info on this forum, thank you in advance.

[joecar]

Some OS's are not compatible... there's a document showing year and OS's compatibilities, see attached:

[wells]

Thank you sir.

[wells]

What about trans?

[Taz]

Similarly to your questions in the other thread ... post your tunes (ECM & TCM) ...

[Hooter]

Hi Guys, Does anyone have a stock Australian 2005 GTO LS2 auto tune please...
There are only manual ones at holden crazy.
I have to replace a HP 2 bar.

[limited cv8r]

Do you know what OS this is. Would one of the other HSV calibrations do the job? e.g clubby,maloo?

[b4pjs]

Have submitted gen-f gts uk variant (VXR8 GTS) stock tune to email link on tunfiledepot but has not been updated yet.