PDA

View Full Version : 98 to 02 swap fuel gauge mess



zapp168
June 3rd, 2007, 09:59 AM
I have read all the information and I think I am doing it right, but I either have the car run perfect, and the gauge pinned, or the gauge look like it works, the car starts, but as soon as I touch the gas pedal the car stalls like it is out of gas :bawl:
I used a tune off of holden crazy with stock 99 tune migrated to 2002 Operating system. system 12212156, and the fuel segment says 16264662. I saw something mentioned about turning on an output in the scan tool? is that what I missed?
:help2:

eboggs_jkvl
June 3rd, 2007, 11:50 AM
Um... Do you have a 98 wiring harness on the car with a 99+ tune?

zapp168
June 3rd, 2007, 11:55 PM
Um... Do you have a 98 wiring harness on the car with a 99+ tune?

Yes I do. I reflashed with a full flash, now the car runs and the gauge works....but it works backwards.....:muahaha:

eboggs_jkvl
June 4th, 2007, 12:24 AM
The 98 harness is wired very differently that the 99+. The pinouts on the 98 PCM don't match the 99+ pinouts. I believe that might have a cause in your problems. You have a couple of choices:

1) get a 99+ wiring harness on the car.
2) change the 98 wiring harness to match the 99+ (Contact "Doc" on this site) by moving around the wires/pins at the PCM
3) Put back the 98 tune and tune with that on the PCM. I have the 98 tuned for my car and it works fine.

Note: using a 99+ PCM wiring with a 98 cluster will have issues for gauge displays

This has the pin out information for the 98 and 99+
http://www.ls2.com/boggs/torques/enginetorques.htm



Elmer

zapp168
June 4th, 2007, 12:33 AM
I have already re-wired the harness. I am driving the car. car runs ok, I have a SES light for EVAP, and the gas gauge is messed up....thanks

shallow bay
June 4th, 2007, 01:46 AM
What kind of vehicle is this for?

zapp168
June 4th, 2007, 01:50 AM
98 T/A, I saw your posts....how is yours coming?

eboggs_jkvl
June 4th, 2007, 02:37 AM
I have already re-wired the harness. I am driving the car. car runs ok, I have a SES light for EVAP, and the gas gauge is messed up....thanks

Now see... I don't see that mentioned in the OP. I guess you have it under control now.

zapp168
June 4th, 2007, 03:52 AM
Sorry, I assume sometimes....anyway gauge works now, but backwards I had to do a full reflash to get it to run right. Now I am going to reverse the settings....keep any ideas coming :)

zapp168
June 4th, 2007, 04:17 AM
BTW Eboggs Your screen name looks very familiar....I think I remember it from LS1.com when I first got my car in 98.....back when there was NO information. My car has an STS on it, and runs as good, even better in someways now with the stock 99+ tune than it did with the professionally tuned 98 computer.

shallow bay
June 4th, 2007, 10:59 AM
I also had the problem with the gas gauge reading backwards after the swap. Try flipping the numbers in {F0501}. Here's how that table looks like in my current tune. I've only put gas in the car once but it looks like the gauge is reading correctly.

zapp168
June 4th, 2007, 11:35 PM
Yup I did that! Seems to work ok now.....I also copied the numbers from the 98, not a 99+ it seems more accurate.