PDA

View Full Version : LMM DEAD tables!!!



1000HP
June 25th, 2007, 11:30 AM
Torque based fuel b1102 in the LMM I have been playing with is throwing a curveball at me. No matter how I adust the table it does not change in the least when logging. And table B1115 also seems to not be responding. I am resorting to the age old tuning method of multiplicity :bash: and my shifting is being comprimised because of it. I need HELP.

pushed2dmax
June 25th, 2007, 05:23 PM
I've also been playing. Seems like I have been getting decent results with the main injection pulse and boost control. What have you been doing with with these tables?

1000HP
June 26th, 2007, 02:15 PM
all of the other tables I have tried are working.

GMPX
June 27th, 2007, 03:46 PM
Very odd indeed, they are the same tables as the LBZ uses (and I assume they work ok?).

Cheers,
Ross

1000HP
June 28th, 2007, 01:29 AM
Ross,

I can send you the tune and some logs if you need.

GMPX
June 29th, 2007, 12:43 AM
No problem, I'll be back on to LBZ/LMM late next week.

Cheers,
Ross

Kennedy Diesel
August 6th, 2007, 11:10 AM
Works for me. I've had some decent results with the LMM so far.

1000HP
August 6th, 2007, 11:13 AM
Well if it tunes basically the same as the LBZ then I don't know whats up. I haven't tried it since the new update. Maybe the old software was the problem.

1000HP
October 21st, 2008, 04:01 PM
I recently bought an 08 LMM and have been having these same tuning issues. I have been tuning other LMMs with these same issues. The LBZs that I have tuned do not have these same issues.
B1161-B1165 do not correlate properly or completely with B1167-B1177. I have entered values in all of these tables that should atleast flare a shift but they don't. I have also maxed out all of the torque limiting tables. I have also ventured into the tcm torque tables to try and fix the problem. The most commanded fuel I am getting is 103 and I am commanding 120.

These PIDS also help when tuning the LBZs and I think they would help with the LMMs also.
- Engine Power Limiting Factor GM.TRQ_FACT_DMA
- Engine Torque Reference GM.ENGTRQREF_DMA
- Main Injection Timing from TDC GM.MAIN1CA_DMA
- Pilot #1 to Main Injection Time GM.PILOT1MT_DMA
- Pilot #2 to Main Injection Time GM.PILOT2MT_DMA
- Pilot #2 to Pilot #1 Time GM.PILOT2P1T_DMA
- Pilot Injection #1 from TDC GM.PILOT1CA_DMA
- Pilot Injection #2 from TDC GM.PILOT2CA_DMA
- Pilot Injection #3 from TDC GM.PILOT3CA_DMA
- Shift Torque State 1 GM.TSFTC1_DMA
- Shift Torque State 2 GM.TSFTC2_DMA
- Torque Limiters Active GM.TRQLIMACT_DMA

Please help!!!

1000HP
October 26th, 2008, 04:13 AM
Update! B1167-B1177 do nothing. I zeroed them out and maxed them out and they had no affect on the commanded rate in the logs at all. Please help Ross!!!

bobo
October 26th, 2008, 04:37 AM
1000hp is right. I have the same results. The people that are saying there is no issue are not changing the factory defuel values enough to see the tables do nothing.

Make the LMM overfuel a shift. That is the best way to show the table is controlling the truck. It is impossible to do with the tables we have now.

You can get good shifts at WOT and good shifts at part throttle. You can't get it to shift perfect like you can on an LLY or LB7 though. That is were these table would help a lot.

Last Sunday I took an LMM out on a 5hr beat run. I had maxed out these shifting tables one by one and seen no difference one way or another. I can get a part throttle defuel at 70mm3 down to 58mm3 no matter where I set the tables. At one point, all the tables were set to 100mm3. That should have caused the truck to fuel from 70mm3 commanded to 100mm3 on the shift. It did not do it.

Danville Performance
October 29th, 2008, 05:46 AM
1000hp is right. I have the same results. The people that are saying there is no issue are not changing the factory defuel values enough to see the tables do nothing.

Make the LMM overfuel a shift. That is the best way to show the table is controlling the truck. It is impossible to do with the tables we have now.

You can get good shifts at WOT and good shifts at part throttle. You can't get it to shift perfect like you can on an LLY or LB7 though. That is were these table would help a lot.

Last Sunday I took an LMM out on a 5hr beat run. I had maxed out these shifting tables one by one and seen no difference one way or another. I can get a part throttle defuel at 70mm3 down to 58mm3 no matter where I set the tables. At one point, all the tables were set to 100mm3. That should have caused the truck to fuel from 70mm3 commanded to 100mm3 on the shift. It did not do it.

x2, SAME PROBLEM HERE. OS#12628594 here, same for you guys I bet...

1000HP
November 1st, 2008, 01:13 PM
Ross,

Do you need any more info or logs from us?

fire0021
November 10th, 2008, 09:45 AM
interesting. is this a 08 os problem or does it affect the 07 os as well ?

1000HP
November 21st, 2008, 02:21 PM
Both 07.5 and 08...try zeroing your torque fuel tables and it will do nothing.

Danville Performance
November 25th, 2008, 03:10 AM
Anything new on the subject guys??

GMPX
November 25th, 2008, 12:33 PM
Well, I think I now understand why changing all those tables to zero would result in no obvious change.
I have added in two more 3D tables that might be the cause of the problem (no guarantee), B1172 & B1176. I call them transient tables but I'm not 100% sure on when they are actually used. The ECM seems to monitor a lot of engine parameters to create a scaler (0-1) used by that table. So for now, it is what it is.

The maths behind these tables (based on the sea level tables as the example is ) -

B1177 x Transient factor = X
B1176 x Transient factor = Y
Then:
X + Y = Z
Then:
B0202 x Z = Final mm3 figure.

So now with some real numbers assumed -

B1177 (110mm3) x Transient factor (0.9) = 99mm3
B1176 (120mm3) x Transient factor (0.1) = 12mm3
Then:
99mm3 + 12mm3 = 111mm3
Then:
B0202 (1.00) x 111mm3 = Final mm3 figure of 111mm3.

So from what I see, even if you zero'd out B1177, the fact that B1176 was not shown (up until this new .calz file) and still had figures in it then you would not see the desired result.

B1177 (0mm3) x Transient factor (0.9) = 0mm3
B1176 (120mm3) x Transient factor (0.1) = 12mm3
Then:
0mm3 + 12mm3 = 12mm3
Then:
B0202 (1.00) x 12mm3 = Final mm3 figure of 12mm3.

But what if the transient factor was the other way around -

B1177 (0mm3) x Transient factor (0.1) = 0mm3
B1176 (120mm3) x Transient factor (0.9) = 108mm3
Then:
0mm3 + 108mm3 = 108mm3
Then:
B0202 (1.00) x 108mm3 = Final mm3 figure of 108mm3.

If you download and extract the attached zip in to the folder -
\Program Files\EFILive\V7.5\Calibrations\E35
You will see the two new tables. I'd be interested to hear if this solves the problem. I think we should be able to come up with a DMA PID to log the transient scaler too otherwise you will be flying blind, or simply make both tables (B1176 & B1177 etc) the same.
Oh also, I noticed an error in table B0202 when looking at this problem, that has been corrected in these .calz files.

:See post below for update:

Cheers,
Ross

GMPX
November 26th, 2008, 12:39 AM
I am sure I've now found the problem, I had defined table B1118 incorrectly, this was not the normal torque limiting table, it was in fact adjusting table B1186 (just added).
This was only defined incorrectly for OS 12628594.
If you are having RPM limiting troubles on the LMM please download these new .calz files for testing and refer back to table B1118, B1119 & B1186 for adjusting. If they are successful they will be released as an auto update for everybody else.

Unzip the attached file in to the folder -
\Program Files\EFILive\V7.5\Calibrations\E35

I also have moved a few torque limiting tables from the Injection Amount group to Torque Limits are they are specific torque limit tables.

Cheers,
Ross

jckleewein
November 26th, 2008, 04:56 AM
I am sure I've now found the problem, I had defined table B1118 incorrectly, this was not the normal torque limiting table, it was in fact adjusting table B1186 (just added).
This was only defined incorrectly for OS 12628594.
If you are having RPM limiting troubles on the LMM please download these new .calz files for testing and refer back to table B1118, B1119 & B1186 for adjusting. If they are successful they will be released as an auto update for everybody else.

Unzip the attached file in to the folder -
\Program Files\EFILive\V7.5\Calibrations\E35

I also have moved a few torque limiting tables from the Injection Amount group to Torque Limits are they are specific torque limit tables.

Cheers,
Ross

Hell Yeah!!! That fixed my RPM limiting issues. I changed the TCM WOT to 4000. She sure did scream to 4000. Thank you for working on this issue. Thanks to the EFI Live Team for making such an awesome tuner.
JC

GMPX
November 26th, 2008, 08:59 AM
Thanks, glad this problem is finally sorted. Actually I am happy it was not yet another limiting table they had put in, but embarrassed it was a silly mistake on my part. I will send the files to Paul to come as an auto update for everyone.

Cheers,
Ross

Danville Performance
December 18th, 2008, 12:09 PM
Thanks agian guys, we were missing the rpm's in a bad way! They sound sooo much better up high!

killerbee
March 21st, 2009, 04:10 AM
does everyone who wants to tune this OS, need this E35 calibration? I am using 7.5.4

Thanks

ScarabEpic22
March 21st, 2009, 11:19 AM
Get 7.5.5 build 83 first, 7.5.4 hasnt been around for a while now.