PDA

View Full Version : E67 supported vehicles & Cal files (Updated 21-October-2008)



GMPX
July 24th, 2007, 12:31 AM
http://efidownload.iqd.co.nz/images/Controller_E67.jpg
E67 ECM Service # 12603530 or 12605843 or 12607096

As of EFILive V7.5.5 we are able to deliver calibration updates and new vehicle support via automated on-line updates. Any new operating systems added to the software will no longer be posted in this thread as zip files to extract prior to a new installation release being made available, your software will automatically download updates.
If you don't have V7.5.5 installed on your PC can can download it HERE (http://www.efilive.com/index.php?option=com_content&view=article&id=48&Itemid=124).

If you have any further questions on E67 vehicle support please email support@efilive.com (support@efilive.com)

Thanks,
Ross

** Hybrid ECM's have a reduced number of tables & parameters, see HERE (http://forum.efilive.com/showthread.php?t=9367) for more details.

Highlander
January 27th, 2009, 03:00 PM
You should add the Colorado 5 cyls... They are using this PCM.. this is an almighty PCM.

GMPX
January 27th, 2009, 03:45 PM
The only E67 OS I've seen on the Colorado is 12620193 which is in that list.

Cheers,
Ross

finishline
January 29th, 2010, 03:44 PM
I didn't know where else to post this. Feel free to move it where ever it belongs.

We are putting a 2007 Impala SS 5.3 in the back of a Pontiac Fiero. I need a little help from the experts. "H0159 Vehicle Speed Output Signal" is marked as "NO" in our tune. We need a VSS to send to the stock 88 Fiero Speedo. If I mark this "YES" what wire does my signal come out on with this PCM? The 07 Impala uses a serial bus for the tach signal. We need a PPM signal for the Fiero. Thanks in advance for your help.

gmh308
February 1st, 2010, 12:41 AM
I didn't know where else to post this. Feel free to move it where ever it belongs.

We are putting a 2007 Impala SS 5.3 in the back of a Pontiac Fiero. I need a little help from the experts. "H0159 Vehicle Speed Output Signal" is marked as "NO" in our tune. We need a VSS to send to the stock 88 Fiero Speedo. If I mark this "YES" what wire does my signal come out on with this PCM? The 07 Impala uses a serial bus for the tach signal. We need a PPM signal for the Fiero. Thanks in advance for your help.

It depends on the calibration that is in the ECM but...

If you are talking E67 then it is probably going to be on C1-39 (E38 pin 57 C1) - if it will work at all. Some dont.

Tacho can be reset to PWM or crank in G1201.

:)

finishline
February 1st, 2010, 02:45 PM
It depends on the calibration that is in the ECM but...

If you are talking E67 then it is probably going to be on C1-39 (E38 pin 57 C1) - if it will work at all. Some dont.

Tacho can be reset to PWM or crank in G1201.

:)

Thanks for the information. I did see the G1201. Can you tell me what connector and pin that signal would come out on?

gmh308
February 1st, 2010, 06:17 PM
Thanks for the information. I did see the G1201. Can you tell me what connector and pin that signal would come out on?

Would if I knew :).

Best shot would be to find schematics for an earlier truck or car using the E67 that had direct connect tacho, or same for ZR1 Corvette, and check them out to find the pin, and then post back here would be appreciated. E38 is pin 57 C1.

Good chance changing G1201 to crank 15/15 you will get a 4 cyl tacho output signal.

:cheers:

khalidmmukhtar
February 17th, 2010, 01:45 AM
Hi Guys,

Does anyone have the BIN files for a 2008 STS-V?
thanks

doubledip
February 17th, 2010, 11:42 PM
E67 - C1 Pin 25 Tacho

E67 - C1 Pin 39 Speedo