Holden VE SSV Missing Calibration 12619077??

[JezzaB]

Hi,
Tried to pull a stock tune out of a Holden VE SSV [MY08] L98 A6 and it doesnt have the calibration file for it and cant read it. Ive emailed the tune to EFILive. Does anyone have it?

Jez

[Tordne]

Have sent the email to Ross just this minute. I assume you're running the latest software version.

[JezzaB]

Have sent the email to Ross just this minute. I assume you're running the latest software version.

Yeah im running the Pre-Release Software

The OS shows as 12619078

Cheers
Jez

[GMPX]

Once I get the Email I'll make a start on mapping it, it's the first 08 model we have seen, looks like they have updated the OS for the 08's.

Cheers,
Ross

[oztracktuning]

The dealers are flashing a customers SSV today with new stuff for the engine and gearbox. The box flash is meant to make things behave much better. I will be able to read them both tomorrow morning.

[JezzaB]

Once I get the Email I'll make a start on mapping it, it's the first 08 model we have seen, looks like they have updated the OS for the 08's.

Cheers,
Ross

I emailed the A6 T43 trans file tonight as I cant read that either (OS 24243170). Hope you get them sorted soon as the owner is Toey as a Roan Sandle to get it tuned.

Jez

[JezzaB]

The dealers are flashing a customers SSV today with new stuff for the engine and gearbox. The box flash is meant to make things behave much better. I will be able to read them both tomorrow morning.

They will be the same as the MY08, you cant read either engine or trans :(

[GMPX]

I'll send the ECM file in the morning. Might be pushing it to get the TCM done though.

Cheers,
Ross

[JezzaB]

I'll send the ECM file in the morning. Might be pushing it to get the TCM done though.

Cheers,
Ross

Appreciate it! Its ok, when the TCM comes it comes. This should keep him happy for a bit and ill get him back ;)

Thanks again
Jez

[GMPX]

Here's the ECM .cal file for the new Holdens.
Save it in to - \Program Files\EFILive\V7\Calibrations\E38

We are expecting a new release before SEMA, this will be included with that of course.

Cheers,
Ross

[JezzaB]

Here's the ECM .cal file for the new Holdens.
Save it in to - \Program Files\EFILive\V7\Calibrations\E38

We are expecting a new release before SEMA, this will be included with that of course.

Cheers,
Ross

Sorry Ross but have you guys had a crack at the Trans Cal yet?

Jez

[The Alchemist]

I was using this Cal file today on a new SSV and found that a lot of the PIDS were not supported when scanning such as octane scaler, burst knk and all the individual cylinder knk retards among others.....are these yet to be programmed into the cal file or something......?

Mike

[GMPX]

I was using this Cal file today on a new SSV and found that a lot of the PIDS were not supported when scanning such as octane scaler, burst knk and all the individual cylinder knk retards among others.....are these yet to be programmed into the cal file or something......?

Mike

Eeerie!!, I just added them in today. PM me your Email address and I'll forward the file to you (gm_enhanced) file.

Cheers,
Ross

[GMPX]

Sorry Ross but have you guys had a crack at the Trans Cal yet?

Jez
Should get it complete by the end of this week.

Cheers,
Ross

[JezzaB]

Should get it complete by the end of this week.

Cheers,
Ross

How did you go on getting the Tras Cals done?

[GMPX]

Slowly, sorry guys.
The minute they are done I will post them up in the Forum.