BB Logging Update Dec 6, 2007

[Blacky]

Download these two files:

http://download2.efilive.com/Software/V7/EFILive_V751_028_69.zip
and
http://download2.efilive.com/Software/V8/EFILive_V811_011_11.zip

Instructions have been updated, see attached Readme_First.rtf file

If you have already upgraded to the new BB logging bootblock, then you do not need to (in fact you cannot) upgrade the bootblock again. Once it has been done you only need to update the V2.05.xx firmware if/when new firmware is released.

There is new firmware that you must program into FlashScan using the programming option in EFILive_Explorer.
It contains a license upgrade event that will occur the first time you boot FlashScan with firmware 2.5.11 installed.

The low power mode is now active. If FlashScan goes into low power mode, it will appear to be switched off. To re-activate FlashScan, press and hold any key (except Ctrl) until the display lights up. It takes a keypress of about 3/4 of a second. Low power mode can be changed or disabled in FlashScan's settings.

Regards
Paul

[SV8346]

all upgrade went perfect, flashes prg cal's in with no problems. Only thing i have noticed is that after updating cal's i cant get scan software on laptop to connect, i have to unplug V2 and shutdown scan software then restart everything to get it to connect.

[Blacky]

all upgrade went perfect, flashes prg cal's in with no problems. Only thing i have noticed is that after updating cal's i cant get scan software on laptop to connect, i have to unplug V2 and shutdown scan software then restart everything to get it to connect.

Make sure that EFILive_Hapi is not still running in the system tray on the task bar. If it is, that will prevent the Scan and/or Tune software from seeing FlashScan.

There may also be a reset issue in FlashScan after reading/flashing - I will investigate it tomorrow.

Regards
Paul

[TAQuickness]

cooooooool. Thanks Paul. If all goes well, I should have my first shot at testing BBL tomorrow.

[Garry]

I see the date setting bug was fixed ... :)

[Goldfinger911]

Looks good. The update was flawless. Flashed my ECU no probs. One little thing, and a few questions...

The splash screen timeout under Settings, doesn't seem to have an affect anymore.

Also, what are these delays:

--Alert?
--Error
--AR Delay?
--AR Speed?

Thanks again mate. Off to the dyno for me. :)

[Blacky]

Looks good. The update was flawless. Flashed my ECU no probs. One little thing, and a few questions...

The splash screen timeout under Settings, doesn't seem to have an affect anymore.

Also, what are these delays:

--Alert?
--Error
--AR Delay?
--AR Speed?

Thanks again mate. Off to the dyno for me. :)

I'll check the splash screen timeout.

Alert (i.e. non-serious errors) is the number of milliseconds that alerts will be displayed. Set to 0 if you want to be required to press any key to clear an alert display.
Error is the number of milliseconds that errors will be displayed. Set to 0 if you want to be required to press any key to clear an error display.
AR Delay is the initial delay in ms before a key will start Auto Repeating.
AR Speed is the delay between repeated keys. Regards
Paul

[Goldfinger911]

Cool. Thanks Paul.

The ReadMe file says that this release has User Defined Audible alarms... how do I configure them?

Thanks.

[Chevy366]

Everything seems o-k , data pass through did not work for me on last update , does now .
Great progress .:D

[Garry]

Yup, looks like we're getting there! :rockon: Good work Paul!

[Ninety8C5]

The splash screen timeout under Settings, doesn't seem to have an affect anymore. :)

I was changing/playing with the splash screens last night and it seemed that every time I changed the screen the splash screen would not stay on for the full 5000 ms that I had set.

I went to the option for the splash screen timeout and it was still set to 5000ms . I pushed the 'OK' button and on the next start up the splash screen stay on for the full 5000ms.

I seems that the timeout resets to the default everytime you change the splash screen even though it is set for a longer time on the option screen, if you do not go and reset it (OK). :Eyecrazy:

[Blacky]

Cool. Thanks Paul.

The ReadMe file says that this release has User Defined Audible alarms... how do I configure them?

Thanks.

http://forum.efilive.com/showthread.php?p=59758#post59758

[Blacky]

I was changing/playing with the splash screens last night and it seemed that every time I changed the screen the splash screen would not stay on for the full 5000 ms that I had set.

I went to the option for the splash screen timeout and it was still set to 5000ms . I pushed the 'OK' button and on the next start up the splash screen stay on for the full 5000ms.

I seems that the timeout resets to the default everytime you change the splash screen even though it is set for a longer time on the option screen, if you do not go and reset it (OK). :Eyecrazy:

Yes, there is something weird going on with the splash screen time. It is not being initialized correctly. I am still looking for it.

Regards
Paul

[Cougar281]

Paul, just FYI, still no LLY BBL or clearing DTC's on the DSP5 OS.

[XLR8NSS]

I'll be able to check out my E38/T43 stuff tomorrow.

[dc_justin]

License adding worked for me.

Locked a PCM to my cable without any problems.

Flashed with no issues. Things seem good.

Still have the periodic flashscan splash screen hang on the V2 itself, but for now, that's minor.

[02Z06]

I'll be able to check out my E38/T43 stuff tomorrow.Hi XLR8NSS, I think you will find everything is OK. I used Flashscan on my 08-Z06 with no problems, I did format some different PID's, ETCTP, MAF, MAFFREQ2. Will load new file in the ECM tonight and get back.

[02Z06]

Make sure that EFILive_Hapi is not still running in the system tray on the task bar. If it is, that will prevent the Scan and/or Tune software from seeing FlashScan.

There may also be a reset issue in FlashScan after reading/flashing - I will investigate it tomorrow.

Regards
PaulAfter Flashing my E38 ECM I went to the scan tool and flashscan would not connect. Pulled USB to reset FS and all was well. BTW thanks Paul for fixing the HO2S11 +2 in the E38 PID's.

[SV8346]

EFI Live hapi was definitely not running and still cant get scan tool to connect after flashing new cal's. I have to reset V2, shut down scan software then restart software and reconnect V2 then it will connect to software.

[Wasted Income]

EFI Live hapi was definitely not running and still cant get scan tool to connect after flashing new cal's. I have to reset V2, shut down scan software then restart software and reconnect V2 then it will connect to software.

I have the same exact problem.

I am also not able to clear DTCs with the V2 in standalone (2002 5.3L PCM). I can't remember the error#, but I'll post it up maybe this weekend.

[lakingslayer]

Paul, just FYI, still no LLY BBL or clearing DTC's on the DSP5 OS.

BBL works for me on the LLY DSP5. Clearing DTC's with the V2 doesn't but I can with the laptop. I just can't get my data to the PC from the V2.

[Cougar281]

BBL works for me on the LLY DSP5. Clearing DTC's with the V2 doesn't but I can with the laptop. I just can't get my data to the PC from the V2.

Hmmm... That's odd. I tried both in my truck with the DSP5 OS and on the bench with my original untouched ECM. Neither would give up data in BBL, but the original would let me clear codes without an error. I tried BBL on a LS1 PCM on the bench and it logged data... :nixweiss:

Any tips?

[Blacky]

Hmmm... That's odd. I tried both in my truck with the DSP5 OS and on the bench with my original untouched ECM. Neither would give up data in BBL, but the original would let me clear codes without an error. I tried BBL on a LS1 PCM on the bench and it logged data... :nixweiss:

Any tips?

Try selecting LLY Manaul (not auto) since we don't have the Allison PID definitions set up for BBL yet.
Paul

[Cougar281]

Try selecting LLY Manaul (not auto) since we don't have the Allison PID definitions set up for BBL yet.
Paul

No dice. Tried both ECMs, both Auto and Manual. Still pulls from the LS1 though...

[Wasted Income]

My LLY with DSP5 will BBL.

[dfe1]

2002 Silverado- bbl works fine, reflash works fine. Reflash screen still says Auto Cal V2 instead of FlashScan V2.

[LBZ_GMC]

I am able to flash LBZ ecm now. Mine say AutoCal V2 as well. Good work guys , your getting there!

[Donovan]

I am able to flash LBZ ecm now. Mine say AutoCal V2 as well. Good work guys , your getting there!


So am I! I did notice that when I flashed the ECM and the tried to open another tuner file and flash the TCM I lost communication to the Flashscan and needed to bounce the device. I think someone else also reported this problem....