PDA

View Full Version : locked ECM



duramaxdaddy29
June 3rd, 2008, 02:56 PM
Boot loader error. What am I doing wrong
? Thanks in advance.
Matt

Status: OK.
19:59:59.783: Bootloader version: DLB7_v1.3C (06E0-0C13)
19:59:59.783: Preparing ECM for reflash...
19:59:59.892: ECM seed is: $6CAE
19:59:59.892: Unlock attempt 1 of 1
20:00:00.141: Initializing ECM...
20:00:00.984: Initializing ECM, step 1 of 4
20:00:00.984: Initializing ECM, step 2 of 4
20:00:01.811: Initializing ECM, step 3 of 4
20:00:03.402: Initializing ECM, step 4 of 4
20:00:08.425: No response from ECM. Retry 1...
20:00:09.704: ECM seed is: $6CAE
20:00:09.720: Unlock attempt 1 of 1
20:00:12.734: ECM is in an unknown state.
20:00:14.871: Clear emisison related DTCs...
20:00:14.903: Clear DTCs for all modules...
20:00:15.261: Disconnecting ...
20:00:15.308: Disconnected
20:00:15.308: Data transfer was interrupted.
20:00:19.601: Done!

horsehaulin
June 3rd, 2008, 10:55 PM
Try try again, and then try again. Thats what happened to me and I finally got it to load!

joecar
June 4th, 2008, 02:47 AM
Did you get your V1 working again...?

duramaxdaddy29
June 4th, 2008, 06:50 AM
V1? joe car

joecar
June 4th, 2008, 07:30 AM
Matt,

Oh... I meant this:
In post #3 of showthread.php?p=72093#post72093 (http://forum.efilive.com/showthread.php?p=72093#post72093) you mention that you now have a new problem...
do you still have that new problem, or were you able to sort it out, or was this thread about the new problem..?

(Oh... do you have a FlashScan V1 or V2...?)

Oh... I have talked myself into a loop, haven't I...:D

duramaxdaddy29
June 4th, 2008, 10:12 AM
Yes this is the new problem Joe, on my friends truck.(the reason I needed the other lincense info) but any ways I have the V2. I downloaded the same tune for my truck and it worked fine. Maybe I should ask this question, How do I get a tune off of the internet and put it in the truck? When I did mine I just copied everything from the tune I got, to my factory tune and it worked awsome but took a while.
Thanks,
Matt

joecar
June 4th, 2008, 10:27 AM
You may be able to find a stock tune at www.holdencrazy.com.

duramaxdaddy29
June 4th, 2008, 10:43 AM
Curious? Why am I looking for a stock tune? I'm kinda slow so remember that.

joecar
June 4th, 2008, 10:59 AM
Curious? Why am I looking for a stock tune? I'm kinda slow so remember that.

Yes this is the new problem Joe, on my friends truck.(the reason I needed the other lincense info) but any ways I have the V2. I downloaded the same tune for my truck and it worked fine. Maybe I should ask this question, How do I get a tune off of the internet and put it in the truck? When I did mine I just copied everything from the tune I got, to my factory tune and it worked awsome but took a while.
Thanks,
MattMatt, I was reading fast... and I saw your question... and as I write this reply I just remembered you're diesel... so just disregard my answer... :doh2:

it seems I have had a long day and am finaly losing sanity... :cucumber::cucumber:

Cheers
Joe
:)

duramaxdaddy29
June 4th, 2008, 01:50 PM
horsehaulin
Junior Member

I tried your earlier post and tried Alt Keys and clicked off of the high speed and it worked the first time thanks guys this place is awesome.
Matt

GMPX
June 4th, 2008, 04:04 PM
Try again with the Try Alt Keys and High Speed 'on', low speed is a last resort but not really something you would want to do all the time as it's MUCH slower.
Also, don't forget, if you have any aftermarket audio equipment like XM adaptors etc these can play havok on the vehicle communications data bus causing all sorts of errors, best to disable (or unplug them) when programming.

Cheers,
Ross

horsehaulin
June 4th, 2008, 04:30 PM
Working on things now!