PDA

View Full Version : Can't log?



Roadrunner
October 23rd, 2008, 01:27 PM
Went to log a run for the first time after 7.5.4.65 and keep getting error code $11 not supported. Probably something I didn't do right!! Thanks in advance for your help. RR

joecar
October 23rd, 2008, 01:30 PM
What vehicle/ECM...?

Roadrunner
October 23rd, 2008, 01:55 PM
Duh!! 06 LBZ I'm still looking for my error. I still have the old 7 version so I see if it run that in the morn. Thanks Joe RR

Jasondt2001
May 12th, 2009, 04:15 AM
any fix? I just got this...

joecar
May 12th, 2009, 07:23 AM
Did you update to Build 84 software...?

And you have to update your FlashScan V2 bootblock/firmware.

Jasondt2001
May 12th, 2009, 09:09 AM
Hi Joecar!

Yes, I'm on build 84 software. I went to EFILive explorer and it then updated my bootblock to the 'latest' available it stated.
I went back out to the truck, tried again, and NOTHING. I then changed the logging mode to dynamic and still same error.

Here's the list it gave me from the scan n tune error:
[quote=scan n tune]
Error report generated by EFILive at 15:04:49 on May 12, 2009

Error code: ERR_RESPONSE/5
Response $11: "Mode Not Supported".

EFILive Version: 7.5.5 (Build 84)

Platform: Windows XP
Version: 5.1 (build 2600)
Processor type: Pentium 1995MHz

Directories
Temporary Cache: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Temporary cache
Logged Data: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Logged data
Customers: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Customers
Configuration: C:\Program Files\EFILive\V7.5\Configuration
Exported Data: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Exported data
Images: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Images
Sounds: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Sounds
Maps: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Maps
Pids: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\PIDs
Virtual Dash: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\VDash
Print Reports: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Print reports
Bug Reports: C:\Documents and Settings\Jason\My Documents\EFILive\V7.5\Bug reports

Connected: No
Com port: 0
Com setup: EFILive FlashScan V2.5: USB
Requested baud rate: 115200

Cable id: 7
Cable code: FlashScan V2
Cable desc: EFILive FlashScan V2
Cable version: 2.6.6
Cable Firmware date: 20081214
Cable model: FSV2
Cable Serial number: 003635578445

Protocols: 0
Protocol list:

Auto connect: No
Scan OBDII info: No

Error retries: 1
Retry delay: 10
Message throttle: 0

Most recently used VIN: 1GTJK33D07Fxxxxxx (Note: 1)

PCM information
Hardware Number: Unknown
Calibration ID: 12606127
Serial Number: 86J628603950
Operating System: 12632483
Engine Operation: 12632640
Engine Diagnostics: 12632655
Engine: 12632720
Not used: 12632666
Fuel System: 12632666
System: 12632677
Speedometer: 12632700
Boot Block: YNAY
Stream-Slow scan mode: Supported
Stream-Fast scan mode: Supported
Maximum dynamic packets: 16

Detected modules:
$11="Engine Control Module (ECM)"
$18="Transmission Control Module (TCM)"

Selected parameters:
CALC.POWER_RW=1,4308
GM.BOOST2_DMA=1,4440
GM.DESTCBOST=1,4478
GM.EGR=1,4503
GM.EGRCOM=1,4504
GM.ENGOILP=1,4517
GM.ENGTRQREF_DMA=1,4519
GM.FRPCOM=1,4599
GM.FRPDES=1,4601
GM.FUELRCALC=1,4614
GM.MAIN1Q_DMA=1,4736
GM.MAIN1T_DMA=1,4737
GM.MNINJTIM=1,4782
GM.PILOT1Q_DMA=1,4851
GM.TCVDES=1,4999
GM.TCVLRNC=1,5000
GM.TCVLRNO=1,5001
GM.TCVPOS=1,5002
GM.TP=1,5027
SAE.AAT=1,5091
SAE.BARO=1,5098
SAE.ECT=1,5113
SAE.EGR_PCT=1,5115
SAE.FRP_C=1,5123
SAE.IAT=1,5126
SAE.LOAD_PCT=1,5128
SAE.RPM=1,5152
SAE.TAC_PCT=1,5158
SAE.TP=1,5159
SAE.VPWR=1,5167
SAE.VSS=1,5168

Jasondt2001
May 12th, 2009, 09:10 AM
If you need ALL of it I'll email it to someone - the forum won't let me post it (as it's too long)

This is on a 07 Dmax LBZ

Blacky
May 12th, 2009, 11:32 AM
The error will be that one of the PIDs in that list is not supported.

Remove one PID at a time until the error goes away which will indicate that the PID you just removed was responsible for the error.

Or send me the entire file (paul@efilive.com) and I can tell you which one it is.

Regards
Paul

Jasondt2001
May 12th, 2009, 01:34 PM
Thanks Paul!!

You got it right on... It didn't like these:
GM.TRQ_fact... engine power limiting factor

GM.PILOT1Q_DMA Pilot injection #1 Fuel Flow Mm3

SAE.AAT Ambient Air Temperature

I deselected them and all is well!!