PDA

View Full Version : No A/F!!



minytrker
November 2nd, 2008, 04:08 PM
I have done the updates, (seemed to all go OK) But now I cant log my air fuel through serial. All I get is controller not found.

Need help ASAP!! Have car sitting on dyno since Friday with still no fix.
I have
bootware 2.06.02
16oct08

firmware 2.06.05
28oct08
__________________

mr.prick
November 2nd, 2008, 04:15 PM
you need to select the WBO2 through the V2.
F4 > F1 > F1 scroll down to WO2 type and select your WBO2 press Ok.

minytrker
November 3rd, 2008, 02:29 AM
you need to select the WBO2 through the V2.
F4 > F1 > F1 scroll down to WO2 type and select your WBO2 press Ok.


Thats all been done. It still says no controller found. It did work until the latest update.

joecar
November 3rd, 2008, 05:07 AM
What WB...?

minytrker
November 3rd, 2008, 06:14 AM
innovate lm1

joecar
November 3rd, 2008, 07:46 AM
Lorenz,

Did you set all of these:
- serial pids = yes,
- com in = wide 02,
- com out = wide 02,
- wo2 type = innovate,
- wo2 fmt = both,
- wo2 data = AFR & EQ.

minytrker
November 3rd, 2008, 09:14 AM
Lorenz,

Did you set all of these:
- serial pids = yes,
- com in = wide 02,
- com out = wide 02,
- wo2 type = innovate,
- wo2 fmt = both,
- wo2 data = AFR & EQ.



Yes,

I even tried changing them and then setting them back to what you have posted.

joecar
November 3rd, 2008, 10:44 AM
And you have the serial AFR cable plugged in...?

And this same cable worked before...?

joecar
November 3rd, 2008, 10:46 AM
I pm'd Paul... he may be on his way to SEMA which starts tomorrow.

minytrker
November 3rd, 2008, 11:42 AM
And you have the serial AFR cable plugged in...?

And this same cable worked before...?


Yes its plugged in. Yeah its worked for a good while, used it daily.

mr.prick
November 3rd, 2008, 11:51 AM
did you format and install all the config files?

joecar
November 3rd, 2008, 02:09 PM
did you format and install all the config files?Good point...

Reformat config tab, and redrag files down to config tab.

minytrker
November 3rd, 2008, 03:02 PM
Yes I tried that also. Is there any other config files for the wb somewhere else.

joecar
November 3rd, 2008, 03:30 PM
I pm'd tech support.

Blacky
November 3rd, 2008, 07:16 PM
There isn't anything else to configure (that hasn't already been said in this thread) that I can think of.

Unfortunately I don't have access to our development systems while I'm in Las Vegas so I can't check exactly what needs to be configured.

If you connect up the wide band and attempt to log wide band data (even though it may not actually log anything), then save a trace file on FlashScan and attach it to this thread I'll take a look.

Regards
Paul

minytrker
November 4th, 2008, 06:53 AM
Its working now. I went through and re-installed everything again and it worked this time. I tried it before with no luck but it worked this time. Thanks for all the replies and help.