PDA

View Full Version : Having problem with dashboard.


Brian1
December 29th, 2008, 12:37 PM
I am connecting to an LMM Duramax ECM. When I goto dashboard the default gauge page shows the gauges but not working like not reading anything. If i hit the yellow button on the dashboard section I get the following error. Now I have activated the DVT and they work at this same point so it seems connected to me since I raise and lower engine RPM from the DVT. I have installed the latest
EfiLive 7.5.5 build 77
EfiLive Explorer 8.1.2 build 44
Bootblock 2.06.02
Firmware 2.06.06

Now it has worked before but that was before the last update. I had build 7.5.5 build 72 and 8.1.* build 42 and worked for me then on same notebook and usb port.

This a portion of the error log.


Error report generated by EFILive at 18:02:38 on Dec 29, 2008

Error code: ERR_IGNORED/4
No response from vehicle.

EFILive Version: 7.5.5 (Build 77)

Platform: Windows NT
Version: 6.0 (build 6001)
Processor type: Pentium 2261MHz

Directories
Temporary Cache: C:\Users\crusher65\Documents\EFILive\V7.5\Temporar y cache
Logged Data: C:\Users\crusher65\Documents\EFILive\V7.5\Logged data
Customers: C:\Users\crusher65\Documents\EFILive\V7.5\Customer s
Configuration: C:\Program Files\EFILive\V7.5\Configuration
Exported Data: C:\Users\crusher65\Documents\EFILive\V7.5\Exported data
Images: C:\Users\crusher65\Documents\EFILive\V7.5\Images
Sounds: C:\Users\crusher65\Documents\EFILive\V7.5\Sounds
Maps: C:\Users\crusher65\Documents\EFILive\V7.5\Maps
Pids: C:\Users\crusher65\Documents\EFILive\V7.5\PIDs
Virtual Dash: C:\Users\crusher65\Documents\EFILive\V7.5\VDash
Print Reports: C:\Users\crusher65\Documents\EFILive\V7.5\Print reports
Bug Reports: C:\Users\crusher65\Documents\EFILive\V7.5\Bug reports

Connected: No
Com port: 0
Com setup: EFILive FlashScan V2.5: USB
Requested baud rate: 115200

Cable id: 7
Cable code: FlashScan V2
Cable desc: EFILive FlashScan V2
Cable version: 2.6.6
Cable Firmware date: 20081214
Cable model: FSV2
Cable Serial number: 003684136154

Protocols: 0
Protocol list:

Auto connect: No
Scan OBDII info: No

Error retries: 1
Retry delay: 10
Message throttle: 0

Most recently used VIN: 1GCHK236X7Fxxxxxx (Note: 1)

PCM information
Hardware Number: Unknown
Calibration ID: 12617102
Serial Number: 86J701301280
Operating System: 12628596
Not used: 12628594
Not used: 12628713
Transmission: 12628594
Not used: 12628702
Not used: 12628695
Not used: 12628694
Not used: 12628715
Operating System BCC: YRLF
Stream-Slow scan mode: Supported
Stream-Fast scan mode: Supported
Maximum dynamic packets: 16

Detected modules:

Selected parameters:
CALC.G_FORCE=1,4286
CALC.POWER_RW=1,4300
GM.BALRCYL1=1,4401
GM.BALRCYL2=1,4402
GM.BALRCYL3=1,4403
GM.BALRCYL4=1,4404
GM.BALRCYL5=1,4405
GM.BALRCYL6=1,4406
GM.BALRCYL7=1,4407
GM.BALRCYL8=1,4408
GM.BAROV=1,4411
GM.BOOST2_DMA=1,4415
GM.EGT2A=1,4481
GM.FLS=1,4555
GM.FRPCOM=1,4563
GM.FRPDES=1,4565
GM.FRPSV=1,4566
GM.IAT2=1,4620
GM.MAIN1Q_DMA=1,4689
GM.MAIN1T_DMA=1,4690
GM.MNINJTIM=1,4733
GM.PILOT2T_DMA=1,4780
GM.TCVPOS=1,4839
GM.WIFV=1,4902
SAE.BARO=1,4913
SAE.ECT=1,4928
SAE.FLI=1,4935
SAE.FRP_C=1,4938
SAE.IAT=1,4941
SAE.MAF=1,4946
SAE.RPM=1,4967
SAE.VSS=1,4983

Thanks for your time and help.
Brian
Blacky
December 29th, 2008, 01:58 PM
Try reducing the number of selected channels of PIDs to 24 or less.
That is not the same as 24 PIDs. Some PIDs use multiple channels.
You can see the selected channel count at the bottom of the PID selection panel on the [PIDs (F8)] tab page.

Regards
Paul
Brian1
December 29th, 2008, 05:37 PM
Thanks for the reply. I have unselected all of them already after posting. Been trying stuff from this post to no avail. Post #14 http://www.dieselplace.com/forum/showthread.php?t=235447&highlight=dashboard
This is on a vista 32bit system. I will give it a fresh try in the morning. Also this is from the console when connecting.

20:44:46.085: Disconnecting ...
20:44:46.756: CAN-VPW Bridge Deactived
20:44:46.756: Disconnected
20:44:51.389: Scanning for EFILive FlashScan V2 USB
20:44:51.405: Autodetect interface ...
20:44:53.277: Interface not detected
20:44:53.947: Scanning for EFILive FlashScan V2 HAPI
20:44:53.963: Autodetect interface ...
20:44:54.150: Interface firmware version: 2.6.6
20:44:54.150: Connection to [FSV2] interface is OK
20:44:54.166: CAN-VPW Bridge Actived
20:44:54.181: Current protocol set to: "ISO 15765 CAN"
20:44:54.181: Autodetect PCM...
20:44:56.256: PCM not detected.
20:44:56.256: Autodetect ECM...
20:44:56.303: Connection to ECM is OK
20:44:56.303: Autodetect TCM...
20:44:56.334: Connection to TCM is OK
20:44:56.365: Current protocol: "ISO 15765 CAN"
20:44:56.412: Interface firmware model: FSV2
20:44:56.428: Interface firmware version: 2.6.6
20:44:56.459: Interface firmware date: Dec 14, 2008
20:44:56.490: FlashScan serial number: 003684136154
20:44:56.506: FlashScan license number: 003684136154
20:44:56.568: Request GM VIN...
20:44:57.286: VIN: 1GCHK236X7F501266
20:44:57.286: Request serial number...
20:44:58.159: Serial number: 86J701301280
20:44:58.175: Request hardware number...
20:44:58.315: Request GM operating system...
20:44:58.347: GM operating system: 12628594
20:44:58.347: Request GM NVM...
20:44:58.643: GM NVM: 12617102
20:44:58.643: Request GM Engine calibration...
20:44:58.674: Request GM Engine diagnostics...
20:44:58.705: Request GM Transmission calibration...
20:44:58.737: Request GM Transmission diagnostics...
20:44:58.768: Request GM Fuel system...
20:44:58.799: Request GM System...
20:44:58.830: Request GM Speedometer...
20:44:58.861: Request GM BCC...
20:44:59.142: GM BCC: YRLF
20:44:59.158: Request GM VAT/IGN Cycles...
20:44:59.189: GM VAT/IGN cycles: 0
20:44:59.189: Request GM oil life...
20:44:59.220: Query support for stream.01 scan mode...
20:44:59.641: Query support for stream.02 scan mode...
20:44:59.797: Calculating number of dynamic packet ID's...
20:45:00.640: Loading generic configuration file: sae_generic.txt
20:45:00.655: User defined calculated PIDs file: calc_pids.txt
20:45:00.655: Enhanced configuration file: gm_enhanced.prn
20:45:01.155: Request GM VIN...
20:45:01.857: VIN: 1GCHK236X7F501266
20:45:01.981: Request GM operating system...
20:45:02.013: GM operating system: 12628594
20:45:02.028: Validating PIDs...
20:45:02.091: Validating Modules...
20:45:02.137: Searching for: "Powertrain Control Module (PCM)"
20:45:04.165: Searching for: "Engine Control Module (ECM)"
20:45:06.193: Searching for: "Transmission Control Module (TCM)"
20:45:08.409: Initialising PIDs...
20:45:08.565: Initialising Modules...
20:45:08.580: Ready.

Thanks again for your time and help Paul.
Brian1
December 30th, 2008, 10:44 AM
I now have it working. The new change I made today was select the Duramax Imperial PID set. I made a new pid set and thought I could use it that way so as not to change the default. So selecting the pid set and all works.

Thanks for your help Paul.
Brian