Flashscan data logging..

Printable View

Show 40 post(s) from this thread on one page

May 3rd, 2009
mr.prick

Hey Joe,
you should take post #157 and make a sticky for serial WBO2 and
BBL options.txt formatting.
May 3rd, 2009
waterbug1999

Quote:

Originally Posted by joecar

Ok, you have to upgrade both software and bootblock/firmware...

After that, do Help->About in scantool (ST) or tunetool (TT) and it should say build 84.

Start EFILive Explorer (EE), goto Firmware tab, click About, it should say Build 44;

Then, still in EE Firmware tab, update the bootblock to 2.06.02 (checkmark Bootblock box) and the firmware to 2.06.06 in that order.

OK.. This should be done. I did not know where to go to see the "build 84" though. EE did say build 44.
May 3rd, 2009
waterbug1999

Quote:

Originally Posted by joecar

After updating the V2 bootblock and firmware (2.06.02 and 2.06.06) as shown above,

read this:
Also, read this:

Ok.. This is done.
May 3rd, 2009
waterbug1999

Quote:

Originally Posted by joecar

Use attached Options.txt file, copy it to:
C:\Documents and Settings\All Users\Application Data\EFILive\V8\Config

Then start EE, goto Config Files tab, drag these files from the upper pane to the lower pane:
LS1B_A.pmm
Options.txt

You only need the pmm file for your car (LS1B_A = 1999+ LS1 with A4 transmission (includes 12212156 and COS5)).

Exit EE, and remove USB cable.

I dont have that.

http://i279.photobucket.com/albums/k.../efilive-1.jpg
May 3rd, 2009
waterbug1999

I tried to open one of my tunes to look at a few things and a pop up window came up saying its a "DEMO". Whats that about?

Also, the icons are still saying 7.5
May 4th, 2009
joecar

Quote:

Originally Posted by waterbug1999

OK.. This should be done. I did not know where to go to see the "build 84" though. EE did say build 44.

In scantool or tunetool go Help->About.
May 4th, 2009
joecar

Where is Options.txt located...?

Jody,

Do you have Vista...?

For Vista, the location is under C:\Program Data\...
May 4th, 2009
joecar

Quote:

Originally Posted by waterbug1999

I tried to open one of my tunes to look at a few things and a pop up window came up saying its a "DEMO". Whats that about?

Also, the icons are still saying 7.5

Do you have the blue card that came with EFILive...?

Open ST or TT and go Help->Register EFILIve and enter all the information from the blue card exactly as shown on blue card (do not enter your name unless the blue card shows your name).
May 4th, 2009
joecar

1 Attachment(s)

Use this Option.txt file...

Copy the attached Options.txt file to either of:

WinXP: C:\Documents and Settings\All Users\Application Data\EFILive\V8\Config
Vista: C:\Program Data\EFILive\V8\Config (I don't remember is this is right).
May 4th, 2009
waterbug1999

Quote:

Originally Posted by joecar

Jody,

Do you have Vista...?

For Vista, the location is under C:\Program Data\...

Yea, its vista.
May 4th, 2009
waterbug1999

Quote:

Originally Posted by joecar

Do you have the blue card that came with EFILive...?

Open ST or TT and go Help->Register EFILIve and enter all the information from the blue card exactly as shown on blue card (do not enter your name unless the blue card shows your name).

I should have it... Just need to start digging thru the closet to see if I can find the box.
May 4th, 2009
waterbug1999

Quote:

Originally Posted by joecar

Do you have the blue card that came with EFILive...?

Open ST or TT and go Help->Register EFILIve and enter all the information from the blue card exactly as shown on blue card (do not enter your name unless the blue card shows your name).

well.. I found my box and nothing in it but a sticker with a bar code on it, my reciept and a EFILive Flashscan sticker.. So, now what?
May 5th, 2009
joecar

I contacted Tech Support.
May 5th, 2009
waterbug1999

Quote:

Originally Posted by joecar

I contacted Tech Support.

O.k... Thanks.
May 5th, 2009
Blacky

Quote:

Originally Posted by waterbug1999

well.. I found my box and nothing in it but a sticker with a bar code on it, my reciept and a EFILive Flashscan sticker.. So, now what?

Send the FlashScan serial number (the one on the bar code sticker) to me ([email protected]) and I'll send you your license details.

Regards
Paul
May 5th, 2009
waterbug1999

PM sent.
May 6th, 2009
waterbug1999

THANKS.. got it working.
May 6th, 2009
waterbug1999

Quote:

Originally Posted by joecar

Copy the attached Options.txt file to either of:

WinXP: C:\Documents and Settings\All Users\Application Data\EFILive\V8\Config
Vista: C:\Program Data\EFILive\V8\Config (I don't remember is this is right).

Hey Joe.. In here?

http://i279.photobucket.com/albums/k...iliveagain.jpg
May 6th, 2009
joecar

Yes, that's the place, copy Options.txt to there... but do the copy using WIndows Explorer.

Then in EFILive Explorer in the COnfig Files tab:
- click Format and let it finish;
- drag Options.txt and LS1B_A.pmm from the upper pane (Config folder) to the lower pane (Config tab).

Then goto the Scan Files tab and drag down the dtc .txt files.

Then goto the Date/Time tab and click Set Now.

Remove the USB cable, now you're ready to goto car for doing BBL.
May 6th, 2009
waterbug1999

I get confused as to window explorer.. where is that.. ugggg.
May 6th, 2009
joecar

WE is the folder display thing you have beneath EE in the picture in post #178.
May 6th, 2009
waterbug1999

There wasnt a config folder.
May 6th, 2009
joecar

Config folder is at C:\ProgramData\EFILive\V8\Config.

Edit: removed space from pathname... [lol] in accordance with Microsoft's pathname convention... :rotflmao:
May 6th, 2009
Blacky

Quote:

Originally Posted by joecar

Config folder is at C:\Program Data\EFILive\V8\Config.

Just one more "consistent inconsistency" from Microsoft. First they created a folder with a space in thename "Program Files" which broke 99% of applications that relied on the fact the filenames don't (and should never) contain spaces.
Then with Vista, they created a folder called ProgramData to augment the Program Files folder. This time no space. So now we have two folders that are designed to "work together" but one has a space and one does not.

What were they thinking? (were they even thinking?)
Bastards!!!!

Paul
May 7th, 2009
waterbug1999

Quote:

Originally Posted by joecar

Config folder is at C:\ProgramData\EFILive\V8\Config.

Edit: removed space from pathname... [lol] in accordance with Microsoft's pathname convention... :rotflmao:

I still don't see where I am suppose to drag that options.txt file.

http://i279.photobucket.com/albums/k...999/config.jpg
May 7th, 2009
joecar

Jody,

Not C:\Program Files\EFILive\V8\Config, but C:\Program Data\EFILive\V8\Config...

Microsoft's attempt to mess with us...:)
May 7th, 2009
waterbug1999

Ok... ill try it when I get back home.
May 7th, 2009
Blacky

Quote:

Originally Posted by joecar

Jody,

Not C:\Program Files\EFILive\V8\Config, but C:\Program Data\EFILive\V8\Config...

Microsoft's attempt to mess with us...:)

There's no space in ProgramData
Microsoft's attempt to screw with us while messing with us.

Regards
Paul
May 7th, 2009
joecar

Quote:

Originally Posted by Blacky

There's no space in ProgramData
Microsoft's attempt to screw with us while messing with us.

Regards
Paul

lol... see that, I can't get over the missing space....:hihi::hihi::hihi::hihi::hihi:
May 8th, 2009
waterbug1999

yea Joe.... I finally did it. lol

http://i279.photobucket.com/albums/k...99/options.jpg
May 8th, 2009
joecar

Jody,

[red = do this one time]

Ok, now connect V2 to PC (for power);

On V2 LCD/keypad navigate down into setup options, select the SD card, and format it; when done, go back to the opening menu.

Then on PC, open EE, goto Config Files tab, click Format (formats the config space).

Then drag these files from upper pane (PC) to lower pane (V2):
- LS1B_A.pmm <--- means: 1999+ LS1 with A4
- Options.txt <---- the same one you copied

Then, goto Scan Data tab, and drag the 4 dtc files from upper to lowe pane (useful for interpreting DTCs).

Then exit EE, remove V2 from PC.

[green = do this each time you log]

Now goto car, ignition key on, connect V2 to car.

If you haven't done this already, or if you want to change pid list do this:
On V2 display, go into Select Pids...
It shows various "pid lists" (i.e. named lists/groups of pids),
Select one of those (e.g. LOOP or TRANS).
Press OK one more time.
Press the ZERO key to start logging.

When finished logging, press CANCEL two times, remove V2 from car.

Connect V2 to PC, Start EE, goto Scan Data tab, drag log files from lower pane (V2) to upper pane (some folder on your PC, you may want to change to a different folder).
In the lower pane, you can delete the log files.
Exit EE.

Using scantool, open those log files.
May 8th, 2009
waterbug1999

ok... i should have the car in the garage tomorrow, so I will try it over the weekend. I just got my N20 bottle filled, bbuuuwwwaaa!!
May 8th, 2009
waterbug1999

Quote:

Originally Posted by joecar

Jody,

[red = do this one time]

Ok, now connect V2 to PC (for power);

On V2 LCD/keypad navigate down into setup options, select the SD card, and format it; when done, go back to the opening menu.

Then on PC, open EE, goto Config Files tab, click Format (formats the config space).

Then drag these files from upper pane (PC) to lower pane (V2):
- LS1B_A.pmm <--- means: 1999+ LS1 with A4
- Options.txt <---- the same one you copied

Then, goto Scan Data tab, and drag the 4 dtc files from upper to lowe pane (useful for interpreting DTCs).

Then exit EE, remove V2 from PC.

[green = do this each time you log]

Now goto car, ignition key on, connect V2 to car.

If you haven't done this already, or if you want to change pid list do this:
On V2 display, go into Select Pids...
It shows various "pid lists" (i.e. named lists/groups of pids),
[B]Select one of those (e.g. LOOP or TRANS).[/B]
Press OK one more time.
Press the ZERO key to start logging.

When finished logging, press CANCEL two times, remove V2 from car.

Connect V2 to PC, Start EE, goto Scan Data tab, drag log files from lower pane (V2) to upper pane (some folder on your PC, you may want to change to a different folder).
In the lower pane, you can delete the log files.
Exit EE.

Using scantool, open those log files.

On the V2 for "select PID list" what do I select? I see there is an LS1 99+ Auto.

But, when I go into option, its doesnt show what PID's are in the LS1 99+ Auto. It just has this.

;Cap1 Cap2 Controllers (Engine&Trans) PSL PCU Hot Key (Ctrl+Fx)
;------- -------- -------------------------- ---------- -------- -----------------
A->, IBPW, LS1B_A.pmm, PSL_A, PCU, 1
B->, O2S, LS1B_A.pmm, PSL_B, PCU, 2
C->, STFT, LS1B_A.pmm, PSL_C, PCU
D->, LOOP, LS1B_A.pmm, PSL_D, PCU, 3
E->, TRANS, LS1B_A.pmm, PSL_E, PCU, 4
May 8th, 2009
Blacky

The new Version 8 "user friendly" black box logging setup software is almost ready to be released, hopefully this weekend.
I recommend downloading it and using it for black box logging setup once it is available.

Look for it on our downloads page here in the next 24 hours:
http://www.efilive.com/index.php?opt...=48&Itemid=133

Regards
Paul
May 9th, 2009
waterbug1999

Quote:

Originally Posted by Blacky

The new Version 8 "user friendly" black box logging setup software is almost ready to be released, hopefully this weekend.
I recommend downloading it and using it for black box logging setup once it is available.

Look for it on our downloads page here in the next 24 hours:
http://www.efilive.com/index.php?opt...=48&Itemid=133

Regards
Paul

I remember last year that the names matched in the "options" file and the V2.

So, I could set this up and use it. which is IBPW in the V2 and select it.. How do I know what group is what in the V2 when the names dont match?

*PSL_A*
;
;Node PIDs (pid1|pid2|...|pidn) Alarm (min:max:style:time*10ms:hold*sec)
;---- -------------------------- -----------------------------------------
PCM, RPM
PCM, VSS
PCM, TP
PCM, MAP
PCM, MAF
PCM, DYNCYLAIR_M
PCM, ECT, -40:110:97:1:0
PCM, IAT
PCM, SPARKADV
PCM, KR, 0:2:147:1:0
PCM, AFR
PCM, IBPW1
PCM, IBPW2
PCM, LONGFT1
PCM, LONGFT2
PCM, HO2S11
PCM, HO2S21
PCM, MFTOTAL
PCM, AFR_LC11
PCM, AFR_LC12
May 9th, 2009
joecar

1 Attachment(s)

Quote:

Originally Posted by waterbug1999

On the V2 for "select PID list" what do I select? I see there is an LS1 99+ Auto.

But, when I go into option, its doesnt show what PID's are in the LS1 99+ Auto. It just has this.

;Cap1 Cap2 Controllers (Engine&Trans) PSL PCU Hot Key (Ctrl+Fx)
;------- -------- -------------------------- ---------- -------- -----------------
A->, IBPW, LS1B_A.pmm, PSL_A, PCU, 1
B->, O2S, LS1B_A.pmm, PSL_B, PCU, 2
C->, STFT, LS1B_A.pmm, PSL_C, PCU
D->, LOOP, LS1B_A.pmm, PSL_D, PCU, 3
E->, TRANS, LS1B_A.pmm, PSL_E, PCU, 4

Did you drag Options.txt to the Config File tab (the lower pane in EE)...?

Copy the attached Options.txt to your folder C:\ProgramData\EFILive\V8\Config
then using EE goto Config Files tab and drag it from the upper pane to the lower pane (with V2 connected).

lol... Paul will have the new V8/BBL stuff out shortly.

:cheers:
May 9th, 2009
bmax

Quote:

Originally Posted by Blacky

The new Version 8 "user friendly" black box logging setup software is almost ready to be released, hopefully this weekend.
I recommend downloading it and using it for black box logging setup once it is available.

Sweet. :grin:
May 9th, 2009
waterbug1999

ok.. I re-did it..

Where is this in the listings?? I am freaking confused.

; __________________________________________________ _______________________
*PSL,PSL_01,PSL_02
;
;Node PID Alarm (min:max:style:time*10ms:hold*sec)
;---- ---------------- -----------------------------------------
PCM, ECT, -40:110:1:1:0
PCM, CYLAIR_M
PCM, DYNCYLAIR_M
PCM, IAT
PCM, LONGFT1
PCM, LONGFT2
PCM, EOPS
PCM, MAP
PCM, RPM, 0:6500:2:1:0
PCM, SPARKADV
PCM, TP
PCM, VSS
PCM, AFR
PCM, HO2S11
PCM, HO2S21
PCM, IBPW1
PCM, IBPW2
PCM, KR
PCM, MAFFREQ

;Caption Active Controllers (Engine&Trans) PCU Hot Key (Ctrl+Fx)
;--------------- ------ -------------------------- -------- -----------------
LS1 98|Manual, Y, LS1A_M, PCU
LS1 98|Auto, Y, LS1A_A, PCU
LS1 99+|Manual, Y, LS1B_M, PCU, 1
LS1 99+|Auto, Y, LS1B_A, PCU
P10|Manual, Y, P10_M, PCU
P10|Auto, Y, P10_A, PCU
P12|Manual, Y, P12_M, PCU
P12|Auto, Y, P12_A, PCU
E40|Manual, Y, E40, PCU
E40|Auto, Y, E40&T42, PCU
E38|Manual, Y, E38, PCU
E38|Auto, Y, E38&T43, PCU, 2
E67|Manual, Y, E67, PCU
E67|Auto, Y, E67&T43, PCU
LB7|Manual, Y, LB7, PCU
LB7|Auto, Y, LB7&AL5, PCU, 3
LLY|Manual, Y, LLY, PCU
LLY|Auto, Y, LLY&AL5, PCU
LBZ|Manual, Y, LBZ, PCU
LBZ|Auto, Y, LBZ&AL6, PCU, 4
LMM|Manual, Y, LMM, PCU
LMM|Auto, Y, LMM&AL6, PCU
Unused, N
Unused, N
Unused, N
Unused, N
Unused, N
Unused, N
Unused, N
Unused, N
Unused, N
Unused, N

; __________________________________________________ _______________________
;
May 9th, 2009
waterbug1999

So how do you tell what is what?? Im getting ready to go back to the old shit.
May 10th, 2009
joecar

Did you do this (2 steps: copy file to folder, then using EE drag it to Config Folder):

Quote:

Copy the attached Options.txt to your folder C:\ProgramData\EFILive\V8\Config
then using EE goto Config Files tab and drag it from the upper pane to the lower pane (with V2 connected).

Did you have V2 attached to your PC when you did that...?

On V2 goto the Select PIDs option, you will see a "list" of PID lists.

Each PID list is a group of pids that will be logged if you select that list.

Show 40 post(s) from this thread on one page