PLX SM-AFR Serial upgrade

Printable View

Show 40 post(s) from this thread on one page

January 12th, 2009
Shupe

Quote:

Originally Posted by CV8IIM6

I've had a bit more time to look properly at the log with the voltage spikes in it and to play around with my DM-100.

Firstly in the log i can see regular spikes (21 in a 12 minute log) to AFR's of 12.5 17.5 and 10 which just isn't plausible.

I decided to set up the DM-100 to display a warning when ever measured AFR is less than 10.1 I then went driving with the V2 not even connected. It was disappointing to see the warning displayed on a reasonably regular basis confirming an issue with the PLX SM-AFR not the V2 or software.

So I'm wondering if i have a poor earth, if the unit was faulty, if my modifications have damaged a component, if my converter chip is faulty etc.etc.

I'll run a new earth, check my connections inside the unit and have a look at the analog output to start with.

expensive experiment at this stage. :doh2:

I too have noticed these spikes on my modified SM-AFR. I remember the DM5 gauge also has these spikes. Betting the spikes on the display correlate with the spikes on the serial output.
February 5th, 2009
CV8IIM6

http://i449.photobucket.com/albums/q...125_175_10.jpg

Has anyone else noticed strange variations with their SM-AFR?

I'm far from having this issue resolved and considering buying another unit, but i have little faith in the product as it's been suggested that this may be a processing issue in all SM-AFR's.

I have had no help from "PLX Support" who despite being told that:

1. I removed the chip and returned the SM-AFR to it's original condition (ie. no MAX 3232 chip and no V2 connected).
2. Powered the unit from a completely independent power supply with nothing else connected to it (ie known good/clean power and earth, no interference).
3. Tested the unit with the engine and ignition completely OFF (ie. no interference).
4. Logged the analog output and found that while it doesn't display the spikes, it is on average 0.2 AFR leaner than the DM-100 gauge.
5. Still notice frequent, random AFR spikes to 10, 12.5 or 17.5 on the DM-100 gauge.

PLX Support Replied by saying "The digital spikes you're seeing may be coming from a poor power supply source or ignition noise" :bad:

I thought i had done a pretty good job of ruling those things out and was expecting the PLX electronics engineers to suggest replacing a particular capacitor or filter on the circuit board perhaps?

Anyway, enough of my red wine induced rant. if someone can assure me it IS possible to get accurate results from a modified SM-AFR i'll buy another one and keep trying. if many others have similar problems i'll look at other options.

:cheers:
February 5th, 2009
JezzaB

I never experienced any of those problems with my SM-AFR when analog or digital but I just dont like I had to mod the crap out of it to get RS232 etc..

But I like my TechEdge 2J1 (www.wbo2.com) better. Ive tested it against quite a few very expensive Autronics etc and its always been within .1 AFR and I only have to use a gender bender on it. RS232 stardard and an Aussie company. For a low cost unit its very good.

Jez
February 5th, 2009
ntae

If you want i can send you my spare SM AFR for you to test your set up
February 5th, 2009
Tre-Cool

I just ordered myself 8 max3232 boards from the US last night and allready have 10 gender benders from my local computer shop.

Paid $10us for the rs232 boards and $3.50 for the male to male gender benders. this way i can plug the efilive cable straight in.

i have my 2 plx's to mod and more than likely a couple of mates as well.

question: what did you guys use to cut through the alloy for the rs232 plug?
February 5th, 2009
JezzaB

Quote:

Originally Posted by Tre-Cool

I just ordered myself 8 max3232 boards from the US last night and allready have 10 gender benders from my local computer shop.

Paid $10us for the rs232 boards and $3.50 for the male to male gender benders. this way i can plug the efilive cable straight in.

i have my 2 plx's to mod and more than likely a couple of mates as well.

question: what did you guys use to cut through the alloy for the rs232 plug?

I scored. Then use a small drill bit and then filed it to size. Dremel would have done the trick but im out of bits.

Jez
February 8th, 2009
CV8IIM6

Quote:

Originally Posted by ntae

If you want i can send you my spare SM AFR for you to test your set up

Mate, that would be fantastic. I'll send you a PM.

Quote:

Originally Posted by Tre-Cool

question: what did you guys use to cut through the alloy for the rs232 plug?

I drilled about a 7mm hole and then used a small triangular file.
February 13th, 2009
aaronr

What size wire did you guys use? Can make the wires a least 2' long or is there a distend requirement?
June 29th, 2009
nonnieselman

whats the leatest on this guys?

i just bought a PLX and would like to do this so i can start tuning my new cam/turbo/meth setup..
July 21st, 2009
SS2win

This thread is the latest.

I did the mod today and it was a breeze. Relocated the two components to make room and mounted the db9/max232 adapter to the back panel. used the cable that shipped with V2, cut the DB9 end off and replaced it with a male gender Db9. wired it so there's no need for a null modem (connected red to 2, black to 3 and white to 5) then configured v2 so it sees the WBO2 on the RJ12 jack. it worked the first try and couldn't have been easier! well, until they ship a TTL converter in the PLX. lol

Show 40 post(s) from this thread on one page