Printable View
A couple of screenshots of the wideband serial interface for FlashScan:
Press F1 to toggle display between Lambda and EQ Ratio.
Press F2 to toggle display between two separate controllers. (Note that a second LC-1 was not connected so "Controller Not Found" is displayed for controller #2).
Press O to to perform a free-air calibration on an LC-1.
I expect to release the beta firmware tomorrow night.
It will include the BB Logging update as well.
Regards
Paul
Will this be a full install for the beta or do I need to install the current beta and then this update?
Al
Will this first beta be for only LC-1, or will the other controllers that have been talked about like my Tech Edge be supported as well?
For those of us who have a Innovate Product , this is like Christmas in March . :santa2: :unwrap:
:cheers:
/bow
but this will also work for an LM1 right?
It's always Christmas here!
Paul - Your V2 is nude! We normally ban folks for posting nudy pics on the forum, but, since you're the man and all, I think we can let it slide just once.
It will most likely be a full install.Quote:
Originally Posted by ChipsByAl
Regards
Paul
The following controllers are supported now:Quote:
Originally Posted by kbracing96
LC-1 (up to 2 LC-1s may be connected)
LM-1 (up to 1 LC-1 and 1 LM-1 may be connected)
PLX SM-AFR (up to 2 PLX's may be connected)
TechEdge 1.5
TechEdge 2.0
JAW
AEM UEGO
And, still waiting to hear back from FJO regarding their serial data format.
Note: Only the LC-1 has been comprehensively tested, the others have all been developed from their respective manufacturers' data sheets. So there may be some initial teething problems with reading the serial data.
Regards
Paul
Yes, but see note in previous post about teething problems.Quote:
Originally Posted by Highlander
Regards
Paul
Woohoo! Im toey as a Roman sandle to try this out!
Jez
Now that is cool! :cheers:
Time to scrounge up a null modem cable.
will this be a full beta release, or an update?
i might be brave enough to try this one.
It will be a full release - no pre-requisites required.
Regards
Paul
Thanks Blacky, can't wait.
Al
This is great! Long time coming, but as always, worth waiting for!
Blacky for President.
was ther ever an update one the fjo serial info.
the V2 supports FJO now.
Is FlashScan capable of logging 2 Innovate WBs that are chained together?Quote:
Originally Posted by Blacky
Its implied from what I've read above, but wanted to find out before I wire it up.
Oh, wow, I thought this was a new post...
Yes, any two of LC1, LM1 or LM2 (or any combination of two of them) can be logged simultaneously.Quote:
Originally Posted by TFZ_Z06
Regards
Paul
how do i hook up the serial port to the fjo. i have the 4000 model not the 4001 will it still work? it dosent have a serial port on the controller but the manual says it can be hooked up to a pc.Quote:
Originally Posted by mr.prick
paul
im relatively new to efi live ,, i mean i have read alot and then some more ,, i dont usualy ask questions as i like a challenge to figure it out with the plethora of info this site provides,,, now dont laugh but i cant get my v2 to connect to my innovate lm1 ,, ive set the settings as per forum threads and double checked with tutorials ,, connections are right i got latest software version on laptop
should i use my plx sm afr?????
Which wideband do you have...? What engine RPO...? What year/model/vehicle...? What mods...? What V2 firmware version...?Quote:
Originally Posted by MENIOS
YEAH !! whats up with thatQuote:
Originally Posted by TAQuickness
LOL I guess I should pay more attention to the date on a post
Is the cable wired correctly?
Look at this: TAQCables sLM1.pdf - TAQCables sLM1
Car is holden vy 04 a4 cam 222 222 112 at 50 kpac springs and 1/ 78th 4 into ones my lm1 is not black its like a off white i bought it new years ago . It works great infact i use it to win arguments against friends with shit meters. Firmware ? I dunno.. efi live 7.5 does my lm1 need update or trip to the bin?
Cool, long tube extractors with large primaries :cheers:Quote:
Originally Posted by MENIOS
Ok, did you install builds 130 and 111 from --> here.
Then, after installing those, start EFILive Explorer (EE) and update V2 firmware to 2.6.40.
Then, in the V2 options, are you setting:
- serial port to"Wideband",
- wideband to "Innovate".
Then, are you using some form of null-modem adapter (either an in-line adapter, or a wire-swap in your cable)...?
As far as I know, all LM-1's support serial data out... you might want to check the sensor itself (have you seen the video using a rag sprayed damp with brake cleaner, the rag is wrapped around a hot sensor, a good sensor causes a steady rich reading, a bad sensor causes a momentary rich reading followed by a steady lean reading).
Cheers
Joe
:^)
thanks for info joe ill get those builds in asap ... didnt know about that ,, just thought it was plug adjust settings and play
DAMNNNN i thought ud love the big and long primaries ,, love being different ,, down here everyone runs 1 3/4 i made 397rwhp through auto 307 ratios,, and didnt lose any bottom end ,, i was rather proud of it lolololol injectors clipping the 100 percent mark though ,, BETTER CHANGE THOSE!!!!!
hey joe
i downoaded 111 and the 130 i ran them up ,,, then i ran explorer it immediately asked to update so in turn i i clicked yes,, it updated the boot block then went into dead poll,,, while there it told me it will stay in dead poll untill i updated the firmware so i clicked yes ,,, now i unplugged refreshed and checked status on updates ... it states 2.06.03 for bootblock and firmware 2.06.40,,, im just checking cuz you instructed 2.6.40 im assuming thats it but im just following orders ... the thing i was worried about was i read in the help section it states IF THE UNIT IS IN BOOTBLOCK even though it ses its successfully done its not!!!! please advise on my anxiety hahahaha for now im gonna connect analogue as i know ,,, even though superhuman ,,, you must sleep
Yes, that is correct, both bootblock 2.6.3 and firmware 2.6.30.
Does your V2 boot up (and show a menu) when you connect it via the USB cable...?
boots up ,,, within 3 seconds shows
scan tool
tune too,
diagnostics
options
Ok, now start the Scan&Tune software, goto F6 Device Settings, goto F8 Serial IO tab, set Com Port to Wideband, set Wideband to Innovate, Save [to file], Program [into your V2], exit from Device Settings.
Now connect the LM-1 to V2 via the supplied serial cables joined using a null-modem adapter (or a cable made like this)... it specifically has to do the "null modem" Tx/Rx wire swap...
Power up your LM-1, your V2 should show the AFR/Lambda/eqr (dive down the menus to the right screen).
If you want to do BBL/BBR, then in S&T goto F5 Black Box Settings and set up the pidlists/pids/PCM/TCM on the Scan Data tab, and set up the PCM on the Tune Data tab (if you have manual trans leave the 2nd controller blank).
Why do they make this so complex,. Pids and files save here update that,. I love my motec! Thanks joe i have wasted your time lm1 is frozen im ready to smash it to peices, i cant win. I got the plx out now trying to figure a cable out for it is there a way i can use it without that stupid chip on serial port. Which i cant find anywhere. ?
Without the serial modification to the PLX device you can use it with the 0-5 volt A/D input on the FlashScan device. The downside of course is the more complex wiring, and more importantly the less accurate readings.
You have probably spent the money already, but these are the devices that are serially supported (http://www.efilive.com/index.php?opt...138&Itemid=143). I personally have 2 x LC-1 controllers, but I'd probably go the TechEdge route next time...
Here is a thread on the serial mod for the SM-AFR (http://forum.efilive.com/showthread....Serial-upgrade).
JAW
Website: Unknown
http://14point7.com
Thanks for that :). Have updated the page now, and am adding the ECM and Zeitronix a well which are supported.
thanks all !!!!!!!!!!!