-
trouble reading pids
hi my brothers truck pcm can be read and tuned but not scanned...
i have 2 other trucks that scan no problem
with the v2 attached to the odb 2 and the v2 connected to my laptop i enter the vin in the scan tool select the engine size also....
so far so good! the pids have no x through them and appear to be supported!
now i click connect, yellow button in the scan tool
only 3 pids are valid ... the rest have a red x and there is no data from any selected or valid pids
truck is an 03 sierra 1500 5.3 lm7
please help
-
1 Attachment(s)
-
Post screenshots of these tabs from scantool right when the connections fails: Console, OBDII->Summary, OBDII->Modules, OBDII->Controller, PIDs.
-
I have recently ran into the same problem with my 2000 Corvette. 2004 Escalade worked fine but the Corvette would only report Air Mass Per Cylinder, Injector Duty Cycle Bank 1, Injector Duty Cycle Bank 2, and Power At Wheels. However, nothing would record when the red or yellow bttons were activated.
Console
10:54:56.666: EFILive V7.5 Version V7.5.7 (Build 283)
10:55:08.007: No interface cable found.
10:55:08.553: Ready.
10:55:11.252: Ready.
OBD II Summary
The following table is a summary of onboard information extracted from the PCM.
DESCRIPTION STATUS
Supported parameters available 88
Validated modules available 9
System readiness test (EPA) Not checked yet
Specifically monitored tests Not checked yet
O2 sensors tests Not checked yet
Diagnostic trouble codes Not checked yet
History freeze frames Not checked yet
Stream-Slow scan mode Not checked yet
Stream-Fast scan mode Not checked yet
Maximum dynamic packets Not checked yet
OBD II Summary
Modules detected
The following table lists on board OBD II modules and their Module ID.
Modules will vary from model year to model year.
DESCRIPTION ID
"Powertrain Control Module (PCM)" $10
"Traction Control System (TCS) or Electronic Brake Control Module (EBCM)" $28
"Body Control Module (BCM) or Dash Integration Module (DIM)" $40
"Inflatable Restraint Sensing and Diagnostic Module (SDM)" $58
"Instrument Panel Cluster (IPC)" $60
"Radio (RAD)" $80
"Driver Door Module (DDM)" $A0
"Front Passenger Door Module (FPDM)" $A1
OBD II CONTROLLER
(NONE SHOWN)
PIDS[U][B]
OK DESCRIPTION CAPTION UNITS SYSTEM CH PARAMETER
Y Air Mass Per Cylinder CYLAIR Grams/cyl Air 0 CALC.CYLAIR
Y Injector Duty Cycle Bank 1 INJDC1 % Fuel 0 CALC.INJDC1
Y Injector Duty Cycle Bank 2 INJDC2 % Fuel 0 CALC.INJDC2
Y Power At Rear Wheels POWER_RW kW,HP Performance 0 CALC.POWER_RW
- Absolute Throttle Position TP % Throttle 1 SAE.TP
- Air Flow Rate From Mass Air Flow Sensor MAF Grams/s,Lbs/Min Air 2 SAE.MAF
- Commanded Air Fuel Ratio AFR :1 Fuel 2 GM.AFR
- Engine Coolant Temperature ECT °C,°F Temperature 1 SAE.ECT
- Engine RPM RPM RPM Conditions 2 SAE.RPM
- Fuel System FUELSYS Fuel 2 SAE.FUELSYS
- Heated O2 Sensor Voltage Bank 1 - Sensor 1 HO2S11 mV O2 1 GM.HO2S11
- Heated O2 Sensor Voltage Bank 2 - Sensor 1 HO2S21 mV O2 1 GM.HO2S21
- Ignition Timing Advance for #1 Cylinder SPARKADV Degrees Spark 1 SAE.SPARKADV
- Injector Base Pulse Width Bank 1 IBPW1 ms Fuel 2 GM.IBPW1
- Injector Base Pulse Width Bank 2 IBPW2 ms Fuel 2 GM.IBPW2
- Intake Air Temperature IAT °C,°F Temperature 1 SAE.IAT
- Intake Manifold Absolute Pressure MAP kPa,PSI Air 1 SAE.MAP
- Long Term Fuel Trim - Bank 1 LONGFT1 % Fuel 1 SAE.LONGFT1
- Long Term Fuel Trim - Bank 2 LONGFT2 % Fuel 1 SAE.LONGFT2
- Retard Due to Knock KR Degrees Spark 1 GM.KR
- Vehicle Speed Sensor VSS KMH,MPH Conditions 1 SAE.VSS
-
In scantool, go Edit->Properties->Connection and set Preferred Cable Type to EFILive FlashScan V2.5 HAPI, and click Ok.
-
Thanks Joe, I will do this later today and let you know the results.
-
Just check my scantool. It was already set to the V2.5 HAPI. Problem still exists when I loaded the Imperial PID selection, only three were reported and all the other were non reporting with the RED X. Ran the DTC and have U1096, U1064 and U1016 H codes. Somehow the OBD II connection is not being recognized by EFILive V2, yet it will power up the V2 FlashScan.
-
After trying to log data, select the menu option: File->Generate error report, send the error report to me at paul@efilive.com, include a link to this thread so I know what its about. I'll see if I can determine what has gone wrong.
Regards
Paul
-
-
Hi Guys, I am having similar problems and will email you Paul with my error reports