Search:

Type: Posts; User: jet231; Keyword(s):

Search: Search took 0.00 seconds.

  1. Wideband 5v output between efilive and aim dash

    Hey guys,

    Just after some thoughts.. I have wideband controller which will output 0-5v, which I have bough to wire to my AIM dash. Ideally, I would like to tune with this wideband as well, so I...
  2. Replies
    3
    Views
    2,383

    Awesome thanks guys!

    Awesome thanks guys!
  3. Replies
    3
    Views
    2,383

    LS1B convert from cable to DBW

    Hi guys,

    Got a quick question. I currently have a 2001 ls1b PCM running a 12225074 OS and 92100254 cal which I changed to a COS 5 - 01290005.
    I'm now swapping the engine into another vehicle and...
  4. Replies
    0
    Views
    1,605

    P0654 Engine Speed Output Circuit

    Hey guys, I am having a drama trying to get my tacho to work with my LS1B Ecu. I'm running an autometer tacho and have wired the car and engine from scratch.. It is an LS2 using an LS1B ecu and...
  5. Replies
    2
    Views
    2,754

    Can anybody confirm? I'm not running any signal...

    Can anybody confirm? I'm not running any signal converters. Just a direct feed from pin 10 to tach. No error messages either
  6. Replies
    2
    Views
    2,754

    No tacho signal from ECM?

    Hi guys,

    I have an LS1-b ecu with the red and blue connectors and am trying to get my autometer tacho working with it. Motor is in a new chassis, so there is no existing wiring. Basically from...
  7. Replies
    3
    Views
    3,956

    I will try and get a log of those 2 pids. There...

    I will try and get a log of those 2 pids.
    There is no analogue connection, only serial. I am using a modified serial comms cable.. my thoughts are that if tx and rx are backwards, it wouldn't read...
  8. Replies
    4
    Views
    4,025

    + is 12v ref, - is ground, O is signal

    + is 12v ref, - is ground, O is signal
  9. Replies
    3
    Views
    3,956

    MTX-L not logging correct

    Hi,

    I have an Innovate MTX-L hooked into my flashscan V2 via serial connection and it currently won't read correctly. For example, it will read around 7.51 on efilive scan and 14.7 on the...
  10. Replies
    4
    Views
    4,025

    All good thanks. It was as we thought

    All good thanks. It was as we thought
  11. Replies
    4
    Views
    4,025

    Cam sensor wiring pinout

    Hi guys,

    I have an 05 model ls2 with the 24x and 1x trigger wheels. Using a cam sensor in the timing case GM part no:12585545. Would anyone know what the pinout should be for this sensor? There...
  12. Replies
    15
    Views
    9,558

    Yeah sorry the b5909 table was just something I...

    Yeah sorry the b5909 table was just something I was playing with. Tried high and low and forgot to change it back.
    Commanded fuel when cranking is untouched from stock.
    Main VE and cranking ve was...
  13. Replies
    15
    Views
    9,558

    Tune file attached. Small log file also...

    Tune file attached. Small log file also attached. I'm starting to think the injectors may be sticking. They have been professionally cleaned about 6-8months ago but might have jammed from sitting...
  14. Replies
    15
    Views
    9,558

    I bought a 2bar map. Delphi p/n281397776. Same...

    I bought a 2bar map. Delphi p/n281397776. Same dramas though. Scaler set to 190 and offset 10. 100kpa with key on.
    Anyone care to have a look at the tune? Need a fresh set of eyes..
  15. Replies
    15
    Views
    9,558

    Yeah it will be a bit delayed but it will be...

    Yeah it will be a bit delayed but it will be tuned to suit. I think I will try another MAP sensor after reading that thread. Cheers for the help guys. Sounds like the exact problem I'm having.
  16. Replies
    15
    Views
    9,558

    I have two bosch 044's feeding a -8 hose to the...

    I have two bosch 044's feeding a -8 hose to the fpr. From the fpr I have a -8 hose running to the front splitting into two -6 feeds for the rails. I have a return hose from the reg back to the...
  17. Replies
    15
    Views
    9,558

    Trouble with COS5 and 60lb injectors

    Hi,

    I'm currently trying to get my car running on a COS5 system. The operating system is 01290005. It is an ls2 turbo engine with 3.3bar MAP (MAF-less) and using siemens deka 60lb/hr injectors. ...
Results 1 to 17 of 17