Hi,
Reduced to 30 degrees in those areas helped.
No pops yet though....
Regards
Gav
Type: Posts; User: Gav; Keyword(s):
Hi,
Reduced to 30 degrees in those areas helped.
No pops yet though....
Regards
Gav
Hi,
How much should I retard the timing? Running around 37 in those overrun areas atm, gonna try 30? Or do I need a lot more?
Regards
Gav
It's an M6 btw
Thanks Joe,
Will spend weekend trying to do it.
Regards
Gav
Hi Joe,
NTK AFRM NGK
How do i know which air mode i am in?
0 to 64 ?
In B4107 it tells you which CL mode in but one of the axis is SAE.MAF and i dont have a MAf...?
Regards
Gavin
Hi all,
LS1 T56 0411 LS1B running COS3
Have log headers with NBs in just before merge into GT45 Turbo.
I want to try to get my NB reading closer to my WB(in downpipe from turbo)
In B3647 i have...
Ahhh wasnt notified anyone replied. Thanks though both.
Will look into it abit more
Regards
Gav
Hello,
Hope all well.
I would like to increase my engine braking as trying to fine tune.
I have efilive and understand may be the throttle follower cracker tables
When if accelerating and i...
Hi Joe,
COS3 , needed cax file b from above link, not tried it yet though, have set b9021 to 0.125 same as other tables. Hoping it will fix rich idle...
Regards
Gav
Ok was using wrong cax, have now seen b9021 and set same as b4003 and b4004 at 0.125. Will see how it goes now...
Link for cax was...
Hi,
hope someone can help.
installed new injectors fic 60lb and corrected data in tune.
ran it up and running very rich on no load.at 12 afr at idle.
Read here and efilive forum may need cax...
Hi Joe,
Hoping you would reply.
Yes i used the scaler to set engine off key on value to 101kpa.
Think i may have a 2.5 bar sensor as results in first post.
With my vac pressure pump at...
Hi,
hope someone could chip in..
just installed a 2 bar map sensor
got on the box Auto sensor standard parts PRC, OEM LS 2 bar
Think it was sfi...?
Anyway with old sensor key on Map was reading...
Joe, 15 for MAP seems stock as well ?
Can i just full flash my created cos3 tune back in or have to do it two steps as per original tutorial?
Regards
Gav
Hi both,
Jim, have saved and removed out of range values.
Have copied high and low from z06 tune to cos3 tune.
Joe, i am in open loop(no o2 sensors) and SD and trying to VE tune as well.
...
Thanks for that Jim,
will try that but first i threw my old non COS operating system back in as didnt want to do any damage etc. Can i just full flash the cos3 above back in , in one go, or should i...
Hello,
Ok i must have missed something out or done something wrong2109221093
I updated to COS3 and went for a run after following tutorial and logged.
The spark now has gone high (i have no MAF...
Oh crap, i probably havnt attached my pids, dont have any smaller logs yet.
Regards
Gav
Hi Joe,
Not sure how i get the MAP into V7.5 thats why persisted with V8 to get this far
When i open the log in V7.5 my custom pids for afrNTK and ben dont appear...?21025
Thanks for looking...
Hello,
I have analog WB NTK not NGK but have set up my own pids for my wideband. Trying to do all this with V8 scan software.
I am stumbling on the MAP bit in V8 Scan software.
My BENS are showing...
Hi Joe,
i did post here http://ls1tech.com/forums/pcm-diagnostics-tuning/1854836-12208322-auto-12212156-manual-os-required.html
In your opinion do you think i should change to the manuel operating...
Hello,
Might be silly question but getting ready to finally tune with AutoVE as i will be able to drive on UK roads very soon.
My question is why copy Hi spark tables to Low tables?? I thought...
Hello again,
had time to browse here and ls1tech and maybe my problem with cruise control feeling might be that my tune is for an auto, but my swap is a t56 6 speed manual. Looking at other posts my...
Jim,
Your p1 is now in eh? Also the 230 cam. What you putting down if so? So jealous as this is the way i want to go. Are you on stock heads as well?
regards gav
Will post results joe. Probably be a while before i can drive it again now as will be waiting for uk iva test.
Jim, is that you from uk cobraclub?
regards
gav
Hello,
fast idle and idle both passed without me altering tune. All i did before going this time was wrap my sidepipes as they exit the body. So IVA test here we come and if i need to up the lambda...