Search:

Type: Posts; User: nm2769; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Do you have any of the other codes from these...

    Do you have any of the other codes from these slides? Thanks
  2. Tune and last log. Thanks 23169 23168

    Tune and last log. Thanks
    23169
    23168
  3. Been doing some logging and have found that when...

    Been doing some logging and have found that when MINJSTAT_F 7 is active I'm limiting Fuel. Then it goes to MINJSTAT_F 19 and then I have fuel fueling. From what I have read 7 is normal and should...
  4. Need some help updated tune and now limiting fuel

    Guys I need some help. I have been searching and reading every thread I can find on why tunes lower commanded mm3 and duration at 2800rpm and above. I have checked every limiting table that anyone...
  5. Replies
    42
    Views
    11,332

    Paul, the errors occur at startup. Both V7 & V8...

    Paul, the errors occur at startup. Both V7 & V8 get the errors immediately after the program starts. V8 has what seems like an endless Access Errors at startup and I have to use task manger to force...
  6. Replies
    42
    Views
    11,332

    After this latest update it has left V7 & V8...

    After this latest update it has left V7 & V8 completely unusable. Tried doing a complete uninstall and deleting all files and registry entries and reinstalling. Same issues V7 gets a Stream Write...
  7. Replies
    23
    Views
    8,347

    Sorry it was a computer issue. Tried to use...

    Sorry it was a computer issue. Tried to use anther tuning software and it was having errors as well. Just use that laptop for tuning so I did a reset and all is working well now. Not sure what the...
  8. Replies
    23
    Views
    8,347

    Thanks for the tips but unfortunately that did...

    Thanks for the tips but unfortunately that did not work. Will be creating a support ticket
  9. Replies
    23
    Views
    8,347

    V7.5 & V8 unusable after this update. Tried above...

    V7.5 & V8 unusable after this update. Tried above instructions, did not help. Tried uninstalling and deleting program files and then fresh install. This did not help either still getting same errors....
  10. Replies
    0
    Views
    713

    Please Delete

    Please Delete
  11. Replies
    8
    Views
    2,404

    V8 still wont connect to the ECM. Tried...

    V8 still wont connect to the ECM. Tried everything I know to do. Any suggestions? I want to purchase the Cummins license but not going to spend the money if it wont work.
  12. Replies
    8
    Views
    2,404

    I made some headway this evening but still isn't...

    I made some headway this evening but still isn't working 100%. I uninstalled the V7.5 & V8 software from the lap top. Used IObit to clean any remaining files & registry entries. I down loaded and...
  13. Replies
    8
    Views
    2,404

    The problem I have with saying something is wrong...

    The problem I have with saying something is wrong with the truck is that a $15 OBDII scanner works perfectly. If I plug the V2 in without the computer it powers up fine. If i press any of the buttons...
  14. Replies
    8
    Views
    2,404

    No it will not recognize the ECM V8 pops up a...

    No it will not recognize the ECM V8 pops up a screen that says No ECM Detected.
  15. Replies
    8
    Views
    2,404

    I though that was the case that you can scan just...

    I though that was the case that you can scan just not flash without upgrade. I am running the December 2015 release of the software and the V2 has the correct firmware for that software package.
    ...
  16. Replies
    8
    Views
    2,404

    Unable to Connect CM849

    I can not get my V2 to connect with V7.5 scanning tool. When I try to log my CM849 the V2 goes into pass through mode then just the yellow LED is lit. The V7.5 scanning tool shows that it is only...
  17. Replies
    0
    Views
    546

    V8 Scanning WBO2 Not Working?

    I know it has to be something simple but I just cant seem to figure out what the issue is. I am well versed with V7.5 scanning and the WBO2 data is working in 7.5. I have just started using V8...
  18. Replies
    23
    Views
    3,946

    Have you read this tutorial...

    Have you read this tutorial https://forum.efilive.com/showthread.php?4661-Idle-Tuning-Helpful-Info-Inside ? Sounds like normal idle tuning issues after a cam install. I have had good results...
  19. Replies
    23
    Views
    3,946

    I agree if it runs and drives fine. Leave it...

    I agree if it runs and drives fine. Leave it alone. Don't get to caught up in the counts.
  20. Replies
    23
    Views
    3,946

    What intake and throttle body are you running?

    What intake and throttle body are you running?
  21. Replies
    11
    Views
    8,217

    That was the issue I recently updated to Windows...

    That was the issue I recently updated to Windows 8 and have not ran into this before. Thanks for the help.
  22. Replies
    11
    Views
    8,217

    I am receiving a Speedo Calculator error. I have...

    I am receiving a Speedo Calculator error. I have not seen this error before this version. When I press the Speedo Calculator button I receive pop up window that says

    EFILive Tune - Digital tools...
  23. Replies
    89
    Views
    23,441

    File sent

    File sent
  24. Replies
    89
    Views
    23,441

    I have a 2000 Pontiac GTP that I just read the...

    I have a 2000 Pontiac GTP that I just read the ECU were am I supposed to send the file? Any word on tuning support for this ECU?
  25. Thread: Axis Define?

    by nm2769
    Replies
    3
    Views
    1,637

    Perfect Thanks that cleared it up.

    Perfect Thanks that cleared it up.
Results 1 to 25 of 52
Page 1 of 3 1 2 3