Search:

Type: Posts; User: IdahoRob; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. This is incorrect. The tuning is locked from...

    This is incorrect.

    The tuning is locked from viewing and reading but it doesn't lock the ecm from flashing unless the end user locked the ecm using the V2. If that is the case, then the ecm can...
  2. Thread: shift points

    by IdahoRob
    Replies
    2
    Views
    1,107

    The ecm doesn't control shift points. The TCM...

    The ecm doesn't control shift points. The TCM tune would have to be changed using the autocal for the stock shift points to be adjusted. I'm assuming that your autocal was a ecm flash and not a tcm...
  3. Replies
    14
    Views
    4,507

    We have ecms that i can load your tuning onto and...

    We have ecms that i can load your tuning onto and send it. Call for the costs. Most likely your ecm will be a repairable core but i can put it on the bench harness and see what is up with it.
  4. Replies
    4
    Views
    1,457

    With what the vin shows in that photo, that ecm...

    With what the vin shows in that photo, that ecm will not be recovered on a bench. It will have to be repaired with a new board. SoCal Diesel repairs them.
  5. https://www.youtube.com/watch?v=NIvqsDm0f-4&index=...

    https://www.youtube.com/watch?v=NIvqsDm0f-4&index=10&list=PLChFYmYKQPRr3qhcPogvAQ2xawecczaLm
    This should help.
  6. Replies
    25
    Views
    11,900

    Never mind Paul, we have a saved copy of the...

    Never mind Paul, we have a saved copy of the software.
  7. Replies
    25
    Views
    11,900

    Paul, how do we download version 309? I've been...

    Paul, how do we download version 309? I've been using this without any issues but an employee just updated to 315 and I'd like to go back to the 309 version because I don't want to update firmware...
  8. Replies
    6
    Views
    2,627

    Correct, the other issue you will run into is...

    Correct, the other issue you will run into is that the rail pressure at idle has a limiter somewhere and you cannot use the rail pressure table at idle to raise the pressure. It doesn't do anything...
  9. Thread: LML wishlist

    by IdahoRob
    Replies
    99
    Views
    36,910

    LML wish list: Minimum vane position table. ...

    LML wish list:
    Minimum vane position table.
    Glow plug timer control.
  10. Replies
    6
    Views
    2,627

    Its been that way since LMM tuning can out. It...

    Its been that way since LMM tuning can out. It has been brought up in the past but nothing has been addressed. The RPM scaling is off in the DSP tables, you'll have to tune around it.
  11. Replies
    60
    Views
    40,401

    Sticky: I think there is some confusion. EZ Link is not...

    I think there is some confusion. EZ Link is not Ben, EZ Link is a cloud based tuning product that has switchable LML tuning.

    As Tony mentioned, it's what the customers are asking for. Like the...
  12. Replies
    28
    Views
    16,446

    Does the remote link/unlink code work for all the...

    Does the remote link/unlink code work for all the autocals the tuner has sent out with the same V2 license, or does a new code need to be generated for each individual autocal on a case by case...
  13. Thread: Service Regen

    by IdahoRob
    Replies
    9
    Views
    4,092

    I have not seen anything but GM equipment that...

    I have not seen anything but GM equipment that can do a manual regen on GM diesels. There are other tuning products out that have the option but do not work in my experience. I don't expect that...
  14. Replies
    5
    Views
    2,038

    It'll run, but sometimes small things like the...

    It'll run, but sometimes small things like the 4x4 light, etc can act up. You can try it and if there are issues then Tony @ Ridgerunner sells stock tunes.
  15. There was a LMM operating system that had this...

    There was a LMM operating system that had this problem. GM updated the OS to 12628594 which fixed this issue. GM dealer should be able to flash over the tune in the truck, or your V2 can do this. ...
  16. Thread: Frp

    by IdahoRob
    Replies
    6
    Views
    3,091

    I may be able to shed some light on this Ross. ...

    I may be able to shed some light on this Ross. Working on the fuel pressure tables on the standard LMM DSP5 OS 52628594. Comparing the base fuel pressure tables with the dsp pressure tables, the...
  17. Replies
    12
    Views
    5,231

    Sorry, I misread his post saying that he was...

    Sorry, I misread his post saying that he was already swapping 01,02,03 and assumed OS's. Glad it was corrected.
  18. Replies
    12
    Views
    5,231

    You need to run a 2001 OS for the edge to work...

    You need to run a 2001 OS for the edge to work changing tunes on a 2001 truck. Those are 2002 OS you have listed. Use this OS and it'll work. 01887305
  19. Replies
    7
    Views
    3,117

    30 is somewhat safe, 32psi and you are on...

    30 is somewhat safe, 32psi and you are on borrowed time, over 32psi and it will blow up. Remove the boost valve and see how it does.
  20. Replies
    316
    Views
    81,289

    Darn Sorry guys, I received that from a customer...

    Darn Sorry guys, I received that from a customer and I'm on vacation so wasn't in the office to look things over. I had a premature posting problem.
  21. Replies
    316
    Views
    81,289

    Stock ecm and tcm tunes.

    Stock ecm and tcm tunes.
  22. The autocal needs to be linked to a V2. The...

    The autocal needs to be linked to a V2. The tunes need to be set-up for use for that autocal, from the same linked V2, you can't just order any tunes and load into a autocal. The autocal needs to...
  23. Replies
    37
    Views
    18,185

    Start with the peddle position to desired torque...

    Start with the peddle position to desired torque tables. Make small changes and test. This will help the dead peddle issue with stock trucks.
  24. Replies
    3
    Views
    1,556

    35+ degrees of timing and spinning it past 4k...

    35+ degrees of timing and spinning it past 4k rpm. I'm guessing this is a built engine, if it is not, then I highly recommend you have one ready asap. I bet it hauls butt. You will have a much...
  25. Issue 3: Sometimes, after updating the...

    Issue 3:
    Sometimes, after updating the AutoCal/FlashScan firmware, the "Rebooting" message and green progress bar remain visible on the screen even after FlashScan/AutoCal has finished rebooting....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4