Search:

Wish I could help more, but this thread helped with my idle tuning (actually, all that happened was he took a look at the tune and made a few tweaks hahah):
...

I hear it... the file I posted I went a little too trigger happy on the TF/TC... When I rev at idle, the RPMs hang for a solid 3 seconds before dropping :doh:

Now I am just trying to solve my...

Ok so I loaded up the stock tune, put the 02 timing tables in (damn they are a good bit more relaxed than the stock 99 table :doh2: ). Started it up, it worked, and did a nice big RAFIG up to...

Good to know. Damn band clamps. Thanks.

-J

Yea about those headers... I know the manifold gaskets are good, I changed them about 2 weeks ago. Would a leak AFTER the wideband sensor cause issues? The duals don't fit the QTPs so great, but...

Joe,

I have FlashScan V1. Interesting read about the COS full flash issue... thankfully I don't see myself having that issue with the V1. I will load up the 12156 timing tables and have a go at...

Well I am going to completely start over with my tune. It really wasn't going anywhere, things were just getting real messy, so I figured I would start with a clean slate, considering now I actually...

PM sent goldfinger...

Yes I did. I will double check it when I get home to make sure it hasn't come off (it shouldn't "blow off" per say, since it's pulling vacuum in the intake, right?). Got a pic handy? If not no...

Alright so here is the issue I'm having (kind of a long read). For about 7 months, the car was running real good. Driveability was excellent, it pulled well for the power it had, and no issues. ...

Wow good to know... more motivation for COS5. Thanks.

-J

So I had tuned the car over the past few weeks with the LC1 in open loop, and it had been going pretty successful. Got the A/F in the ~15:1 range cruising, and locked at 12.7:1 at wide open. Nice,...

Well I had it wired up to the B and D wires, not C and D... yea there's a small problem. Wired it up CORRECTLY this time, and much better than before (heat shrink wrap, thermal resistant loom,...

Thanks, and yes I didn't give SHIT for information :bash: and for that I appologize. I appreciate your advice and will give it a try this weekend. I am at work I will answer this post when I get...

So I got my LC1 in and working in the stock spot (tuning for OL), and when it finally starts reading "constant" it is all over the place, as low as 4:1 to 20:1, fluctuating faster than I can read it....

Not sure if this is a dumb question or not, but I figured I'd ask anyhow. I am about to tune OL on the car, and can I RAFIG again? Or would I AutoVE the idle? If this is straightforward then I...

Thank you. I will check it out again tomorrow morning, I have no doubt it should work now. Didn't realize I could just change it later.

-J

OK I think I follow. What I did was change the VIN to my vehicle's specific VIN. Would THAT be causing my issue? That is the absolute only thing I did. Good point, thanks, didn't even think of...

Oh so it's not simplistic user error then, that's refreshing. Thanks, had I known I would've just PM'd them rather than having you pull the leg work.

-J

Yea after I pulled the tune that was on there, I saved the file. As I understand it, I use that file AFTER I flash the "02020005" file, as a calibration only flash. Right? Just getting there is a...

So I am following the tutorial to the T right now... and have run into a problem almost immediately. I pulled the tune that's on there right now, saved it, everything is fine. I hit step THREE,...

Yea that was another question I was thinking about on my way to work today. I currently have an 02 operating system (off the top of my head I believe it's the version that can allow me to jump to...

Thanks for the reassurance. I will check into this this weekend and see how it goes. Are you guys running open loop I assume? And if so, are you running Maf or MAF-less?

-J

I am looking to get some AutoVE tuning done soon... I have the LC1 sitting right next to me, just need a battery that allows my laptop to survive more than 15 minutes. In any case, since I'll be in...

Haven't fired it up since changing the desired airflow, I will do that after work today. Do you have an email address? I have the log saved in my gmail account but don't really feel like...