Dyno'd at 595 rwhp 508 rwtq with 5.5 psi at Triple X Motorsports. We went back to the stock OS, but pegged the MAF out in the process. He tunes with EFILive too and is a great tuner!
EFILive is...
Type: Posts; User: JET LEE; Keyword(s):
Dyno'd at 595 rwhp 508 rwtq with 5.5 psi at Triple X Motorsports. We went back to the stock OS, but pegged the MAF out in the process. He tunes with EFILive too and is a great tuner!
EFILive is...
Wow....there's quite a learning curve to this tuning stuff...
I think I've read this entire forum now and everything tuning related on ls1tech and redhardsupra's blog site and a couple other...
Thanks Joe,
1. My stock OS was 12593358, I upgraded it to 02040003.
Could I do a Full reflash with COS5 and then do a Calibration only reflash with COS3?
Or do I need to start over with...
Thanks Joe.
I will check those things today.
I wish that I would have had time to get the cam dialed in before I installed the bigger injectors and supercharger in. I cranked it a couple of times...
Could someone please help me out and tell me where I went wrong?
1. Reflashed my pcm from OS 12593358 to 02040003 OS.
2. Did a recalibration flash of my stock tune on the new OS.
3. Followed...
Thanks Juhanils1,
I ended up with 1K ohm resistor soldered to only the anode (in series) of the LED and applied my power source to that leg of the resistor. My ground wire went from the cathode of...
Thanks DC Justin,
I'll track down a 2 bar map and try my hand at tuning.
Thanks for all the help guys.
So:
1. Get a 2 bar MAP sensor
2. Reflash with COS5
3. Set IFR for 60 lb mototrons (60@43.5psi w/ rail press @58 psi)
4. Bump up MainVE by ~15%
5. AutotuneVE
...
THANKS!
Would this be the correct 2 bar?
GM 12569241 (AC-Delco #213-1520)
dc justin
What would you do in my situation? What would you suggest?
Thanks
-Jet
Yes....stock regulator.
Wow...you really know your stuff!
Thanks for helping me out. Maybe I can work something up and flash. I hope to crank it tomorrow!
Thanks
-Jet
So...Your MAP ultimately determines your fuel pressure at the rail? I saw the tutorial about installing a fuel pressure sensor on the fuel rail. I guess you could log this against MAP and use the...
As always...thanks joecar.
I'm still going to run with the MAF since my boost level is going to be low (6psi). When I add methanol in the future and more boost I'll go SD 2 bar. Can I run with...
Anyone???
I was looking for guidance/suggestions on tuning my 02 Z06 for the following mods:
D1SC Stage II Procharger 5" pulley (6 psi, I hope)
60 lb Motrons
MTI R1 Cam 232 236 .585 .575 114 LSA
1 7/8"...
I was reading about a QTEC controller that can control the position of electric cutouts. It also says it has automatic open or close by grounding or not grounding the trigger wire. Has anyone wired...
well.....it worked fine for a couple of months, now when I try to connect the console gives "ERROR unregistered interface some features have been disabled". Now all I can do is scan : (
I haven't...
Does anyone have the latest firmware for V1, mine has gone haywire and needs to be reflashed.
Raptor shift lights are nice, but I wanted something even more compact to fit in my gauge pod above my boost gauge. My set up looks awesome. Plus, I've got about 3 dollars tied up in my shift light,...
Joe
You are right, 20 mA is correct...I used .2mA in my equation, that's why I got a different value, good catch.. :master:
Before the resistor, I'm getting a voltage of around .75-.84 volts,...
joe
I'm using a blue LED that is rated at 3.7 volts, .2 mA, with a luminous intensity of 2500 mcd. I soldered a 560 ohm resistor to the anode and applied my +12 volts there and ran an 18 guage wire...
I will check my voltage later tonight and post, I should have already done this when I had everything apart. I'm thinking it will be a very small voltage. These LEDS are pretty sensitive to...
I did two things this weekend.
1. Replaced the wire from pin47 with an 18 gauge one to my LED, was 20 gauge.
2. Hooked the wire back up that previously went into pin47(Skip Shift Indicator...
Add me to the list of EFILive enabled shiftlight'ers!!!:cheers:
Everything was the same on my install as by the write up of jsttry with the following exceptions.
1. PIN47 on my red PCM plug...
jsttry thanks for the write up :cheers:
I noticed the shift light option on my 02 Z06, will have to give this a try.