Search:

Type: Posts; User: Scatfish; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Yes I got it running. The LS1 crank sensor and...

    Yes I got it running. The LS1 crank sensor and the Vortec sbc crank sensor are wired different internally. I had to swap the wires A and C on the harness plug.
    Good luck man! Its been running like...
  2. Sticky: I'm glad you guys have the pics. I'm going over...

    I'm glad you guys have the pics. I'm going over this to try to set up to tune. I finally have my WB up and running. I want tot data log now and start the process.
    Thank you!!
  3. I'm dealing with the same thing in my 95 Camaro...

    I'm dealing with the same thing in my 95 Camaro LT!/24X/0411 conversion. I used the same kit from EFI Connection. I've done the same thing as you have (verified all wiring, all voltage circuits, all...
  4. I'm dealing with the same thing in my 95 Camaro...

    I'm dealing with the same thing in my 95 Camaro LT!/24X/0411 conversion. I used the same kit from EFI Connection. I've done the same thing as you have (verified all wiring, all voltage circuits, all...
  5. Replies
    17
    Views
    12,603

    Fuzzman, Did you ever get this problem...

    Fuzzman,

    Did you ever get this problem resolved?
  6. Replies
    59
    Views
    126,442

    Joe, A lot has happened since I started to try...

    Joe,

    A lot has happened since I started to try to get this AEM Wideband going. I've put my dog to sleep cause of cancer, had hurricane Harvey run 8ft of water through my shop for three days, and...
  7. Replies
    59
    Views
    126,442

    I need to reread thru this and catch back up....

    I need to reread thru this and catch back up. I've dropped off the map since the flood from Harvey. Thank God I didn't leave my V2 at the shop!
  8. Replies
    59
    Views
    126,442

    Joe, I had to take a couple days to do some...

    Joe,

    I had to take a couple days to do some fab work, so I've been out of pocket. After not looking at it for that time, I see what you are saying, and I feel like a dunce. Tunnel vision I guess...
  9. Replies
    59
    Views
    126,442

    Here is where it's saved: 21617 Here is...

    Here is where it's saved:

    21617

    Here is what I see when I select the PID's tab:

    21616
  10. Replies
    59
    Views
    126,442

    "Did you just copy the file calc_pids.txt to the...

    "Did you just copy the file calc_pids.txt to the folder User Configuration, or did you edit it also...?"

    I just saved it like that, and it didn't show up.


    I'll post a screen shot when I get...
  11. Replies
    59
    Views
    126,442

    When the calc_pids.txt file is saved to that...

    When the calc_pids.txt file is saved to that folder, is it supposed to create a list of pids to choose, or the AEM 30-0300.pid to choose, and the list of calc_pids under it?

    There is the LC1 and...
  12. Replies
    59
    Views
    126,442

    I did some more reading, and I understand more...

    I did some more reading, and I understand more about the PID's.





    After looking at the .txt doc, Can the 30-4900 be changed to reflect the 30-0300?

    CALC.AEM1 F050...
  13. Replies
    59
    Views
    126,442

    Thank you Joe!

    Thank you Joe!
  14. Replies
    59
    Views
    126,442

    Here is the pdf link for the 30-0300. When I save...

    Here is the pdf link for the 30-0300. When I save these, where do I put them? I know where the PID's are in 8, and have looked around where they are created, but I don't know how to put them there.
    ...
  15. Replies
    59
    Views
    126,442

    So these will work for the 30-0300?

    So these will work for the 30-0300?
  16. Replies
    3
    Views
    7,432

    Am I understanding this correctly for the AEM...

    Am I understanding this correctly for the AEM 30-0300?

    I just wire a RS232 connector, like it shows in the AEM schematic below (for the serial RS232), use a null adapter, and connect that to the...
  17. Thanks dr.mike, and you too joecar! I'll order...

    Thanks dr.mike, and you too joecar!

    I'll order the 30-0300, unless you would recommend a different WB since I'm not tuning any CANBus vehicles at this point. I'm just trying to tune a spare truck,...
  18. Thanks. I made a hasty decision, but was able to...

    Thanks. I made a hasty decision, but was able to cancel the order for the 0334. Is the 0333 the best choice for the non CAN (0411 and similar) PCM's in your opinion?

    Thanks for the info....I'm...
  19. Is this AEM Wideband compatible with the LS1B 411...

    Is this AEM Wideband compatible with the LS1B 411 PCM?

    I should have asked this before I ordered it I guess......

    21588
  20. Does this WB have an output for non can vehicles,...

    Does this WB have an output for non can vehicles, or is it only for the later model PCM's? I need a WB, but don't plan to try to do anything with a can vehicle currently.

    Answered my own question....
  21. Replies
    4
    Views
    2,485

    Scarab I owe you a Beer, or a...

    Scarab I owe you a Beer, or a case!!:rockon::rockon::rockon:

    That was it!!

    Everything is back to normal, gonna go try to read my tune now.

    Thanks again!!
  22. Replies
    4
    Views
    2,485

    I do need the usb driver, because if I look for...

    I do need the usb driver, because if I look for the Flashscan V2, is reads that the usb driver is unavailable!!

    Thanks, I'll try reinstalling them, didn't think about this.
  23. Replies
    4
    Views
    2,485

    I think I damaged my V2

    I was pulling a tune from a truck to modify and the truck had a bad alternator, the battery had a bad cell too I think. I didn't find any of this out, until after I tried to read it. It would read...
  24. No I never did. I tried to run it as an LS1A but...

    No I never did. I tried to run it as an LS1A but it wouldn't work for me. I just for got about it, and have been getting ready to do the 411 swap. If you do figure it out, I'd like to know.
  25. I'll try those two and see if it works. Here...

    I'll try those two and see if it works.

    Here is the thread I'd found a few days ago mentioned in my post: http://forum.efilive.com/showthread.php?20926-Crankshaft-Variation-Relearn

    Thanks!
Results 1 to 25 of 26
Page 1 of 2 1 2