Search:

Type: Posts; User: cindy@efilive; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    494

    Sticky: Post #1 was updated to beta 51(2). Can you...

    Post #1 was updated to beta 51(2). Can you please confirm you have that installation, not the earlier 51(1).
    After updating, please ensure your firmware and configuration files are updated.

    If...
  2. Replies
    27
    Views
    11,109

    You should be able to recover the ECM following...

    You should be able to recover the ECM following the controller recovery process documented here https://service.efilive.com/kb/articles/controller-recovery-process

    Cheers
    Cindy
  3. We've seen a number of situations where customers...

    We've seen a number of situations where customers think they have an A40, but infact they have an A41 controller. A40 is supported, but A41 is not.

    To check which TCM you have you'd need to...
  4. Replies
    166
    Views
    107,773

    Sticky: I'm not actually sure you could program V2.07.140...

    I'm not actually sure you could program V2.07.140 firmware into the V2 with a 2.04.10 bootblock - I'd suggest that step would fail. It's Saturday here so I can't elevate your support request until...
  5. Replies
    166
    Views
    107,773

    Sticky: Can you please post the firmware version you are...

    Can you please post the firmware version you are trying to program again - the version number does not look right.

    The public release version is V2.07.140 (May 26, 2019)
    The beta release version...
  6. AutoCal can read and flash your new project...

    AutoCal can read and flash your new project without any issue, however AutoCal cannot sign new tunes (ie. tunes you write) for flashing. That permission is only available for FlashScan devices.
    ...
  7. You cannot read any CME controller. The factory...

    You cannot read any CME controller. The factory read restriction prevents reading 2010+ Cummins (CMD, CME and CMF) controllers. Users must obtain a base file to tune with.

    Please refer to this...
  8. Try this...

    Try this https://support.efilive.com/kb_article.php?ref=6659-YAHB-3781


    Sent from my iPad using Tapatalk
  9. Replies
    3
    Views
    2,236

    Email support@efilive.com with the license number...

    Email support@efilive.com with the license number of the device and we will see if we can identify the tuner.


    Sent from my iPad using Tapatalk
  10. EFILive has supported this platform for supported...

    EFILive has supported this platform for supported for 7 years and we've only had 3 requests (all in this thread), I cannot prioritise the developers time to attend to mapping these for 44 operating...
  11. The developer picked 5 key operating systems and...

    The developer picked 5 key operating systems and added the tables for testing. If you have a specific OS you require these on please let me know.

    Save the files into the C:\Program Files...
  12. Replies
    1
    Views
    1,068

    You won't be able to determine the tuner without...

    You won't be able to determine the tuner without the previous owner telling you who tuned it or without EFILive hardware.

    The switch positions and each positions purpose is tuner dependent. What...
  13. Replies
    43
    Views
    17,082

    Sticky: EFILive Licenses to ECM serial number. When the...

    EFILive Licenses to ECM serial number. When the ECM is switched out, a new license is needed. If the ECM is replaced at the request of an EFILive support investigation, a VIN license will be issued...
  14. Replies
    10
    Views
    1,782

    Just to update this thread. The Custom Operating...

    Just to update this thread. The Custom Operating Systems restrictions list documented in the Problems Reading a controller help document do not list E98. ...
  15. Replies
    1
    Views
    899

    $0536 means the tune file was not saved for use...

    $0536 means the tune file was not saved for use with AutoCal - although your AutoCal is linked to your Tuners' FlashScan, the tune file also needs to contain his FlashScan serial to give the AutoCal...
  16. Replies
    9
    Views
    2,073

    No worries Tom. Totally your call. Happy to...

    No worries Tom. Totally your call. Happy to arrange a refund if we can reference it back to EFILive order numbers...

    Cheers
    Cindy
  17. Replies
    9
    Views
    2,073

    As stated above 2019 E92 is supported. E88 or...

    As stated above 2019 E92 is supported. E88 or E90 are NOT supported. At this point they will not be supported due to the additional security measures on these controllers.

    You will not be able...
  18. Replies
    9
    Views
    2,073

    Controller auth generation was based off...

    Controller auth generation was based off controller selection to generate the auth-code. If you manually select E92 as the controller to read, but then attempted to read an E90 the software...
  19. Replies
    11
    Views
    1,531

    I get that same access violation as you. In...

    I get that same access violation as you. In future versions of V8, the [F4: Properties] window will be disabled until a tune file is open. You should be prevented from using all functions that...
  20. Replies
    1
    Views
    1,229

    If it's the second and forth amber lights...

    If it's the second and forth amber lights rotating, then the device is in dead-poll awaiting firmware programming.
    Open V8 Scan and Tune software
    Open EFILive Explorer
    Navigate to the [F12:...
  21. You don't update the AutoCal unless your tuner...

    You don't update the AutoCal unless your tuner tells you to. Your AutoCal software/firmware needs to remain compatible with your tuner's FlashScan device.
    How do i send it in to be checked...
  22. Neither of those codes related to Serial...

    Neither of those codes related to Serial mismatch.
    $053C - The author of the tune file has flagged the file to prevent calibration flashing. The file may only be full-flashed.
    $0533 - An attempt...
  23. Replies
    7
    Views
    2,061

    If you meet the firmware requirement, the most...

    If you meet the firmware requirement, the most likely issue is you have a space at the end of your code.
    If the code does not function, please speak with your tuner so that they can generate you the...
  24. Replies
    1
    Views
    1,138

    Email support@efilive.com. Please quote your...

    Email support@efilive.com. Please quote your original and current FlashScan serial numbers.

    Usually when a device is lost or stolen, we build the new FlashScan to contain the same license number...
  25. Replies
    4
    Views
    1,133

    V8 Tune Tool Development

    For those of you who do not subscribe to our newsletter, we've recently provided some information on our V8 Tuning tool.

    The EFILive Tune Tool continues to progress with tune files now functional...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4