Search:

Type: Posts; User: Tom B.; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. My laptop is running Windows 7 ultimate 64 bit. ...

    My laptop is running Windows 7 ultimate 64 bit. I am thinking it was an issue with my laptop and not the software.
  2. I rebooted my laptop a 2nd time and it started...

    I rebooted my laptop a 2nd time and it started working. I'm not really sure what was going on. Everything works perfectly now. I am using the virtual com port settings.
  3. Found the problem.

    Found the problem.
  4. RR control panel won't launch after latest 7.5 update

    I just installed the most recent V7.5 update and now the RR control panel won't launch.
  5. Replies
    14
    Views
    9,010

    I was able to restore the knock software tables...

    I was able to restore the knock software tables back to within 90% of the stock settings. Using the Road Runner RTACS was a major help in getting the VE and timing maps sorted out. I don't think...
  6. Replies
    9
    Views
    5,843

    1st time out and RTACS works as advertised.

    1st time out and RTACS works as advertised.
  7. Replies
    9
    Views
    5,843

    Thank you. I wasn't sure if the FSV2 would...

    Thank you. I wasn't sure if the FSV2 would communicate through the ALDL to the RR.
  8. Replies
    9
    Views
    5,843

    I have been using the serial configuration. I...

    I have been using the serial configuration. I wasn't quite sure if I needed to anything different as far as physically connecting the cables from the ALDL, the Flashscan,and my laptop with the RR...
  9. Replies
    9
    Views
    5,843

    I wasn't sure if I left the flash/scan w/...

    I wasn't sure if I left the flash/scan w/ widebands in the aldl port, or did I need to do something different.
  10. Replies
    9
    Views
    5,843

    Lc-2

    Lc-2
  11. Replies
    9
    Views
    5,843

    RTACS tuning w/wideband

    I am going to attempt to calc VET with the RR. How do I connect my wideband to do this?
  12. Replies
    25
    Views
    57,745

    Sticky: Yes. Thank you.

    Yes. Thank you.
  13. Replies
    25
    Views
    57,745

    Sticky: Found it. :doh2:

    Found it. :doh2:
  14. Replies
    25
    Views
    57,745

    Sticky: I am finally licensing my RR for Efilive. I...

    I am finally licensing my RR for Efilive. I cannot find cal_links.txt in the latest 7.5 version? Do I have to revert to an earlier 7 version to use the RR?
  15. Replies
    3
    Views
    2,882

    Good point. Although I haven't had any misfires,...

    Good point. Although I haven't had any misfires, I will put that on a post it note so I don't chase the wrong cylinder.
  16. Replies
    3
    Views
    2,882

    Swap the wires for the coils at the PCM and...

    Swap the wires for the coils at the PCM and change the injector bank assignment in the software. There is no other way to change the firing order.
  17. Replies
    14
    Views
    9,010

    I know this is an old post. I had the same...

    I know this is an old post. I had the same problem with a 411 swap on an LT4. After modifying the tables using the 2002 L31 parameters, I had to zero out the {B6244} Knock sensor multiplier "A" I...
  18. Thread: BBL PIDs V2

    by Tom B.
    Replies
    41
    Views
    104,072

    Sticky: Thank you.

    Thank you.
  19. Thread: BBL PIDs V2

    by Tom B.
    Replies
    41
    Views
    104,072

    Sticky: I must be doing something wrong. I cannot seem...

    I must be doing something wrong. I cannot seem to figure out how to load the .calc vet file onto my SD card and have the V@ recognize it. What is the proper procedure? Any help would be...
  20. Sticky: Thanks Joecar and Lastcall. I copied the files...

    Thanks Joecar and Lastcall. I copied the files directly to the pids file instead of the user configuration file. I should probably wear my glasses more often.
  21. Sticky: I must be missing something. When I copy and...

    I must be missing something. When I copy and paste the calc_pids-2.txt I cannot see the additional pids CALC.LTFT CALC.LTFTBEN CALC.VE_Table. can anyone enlighten me?
  22. Replies
    106
    Views
    134,638

    Sticky: Ttt

    Ttt
  23. Thank you. I looked high and low to try to find...

    Thank you. I looked high and low to try to find it.
  24. Need wiring schematic for LC-2 O2 sensor harness

    Help. I purchased a new innovate LC-2 that arrived w/o the O2 sensor. I have a compatible "017" O2 sensor with no connector that I need to adapt and I want to confirm the pinouts for the cable. ...
  25. Replies
    2
    Views
    2,616

    Thank you very much.

    Thank you very much.
Results 1 to 25 of 26
Page 1 of 2 1 2