Search:

Type: Posts; User: limited cv8r; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    4,108

    Kalmaker is still around and is alot cheaper than...

    Kalmaker is still around and is alot cheaper than what it used to be, with a modified ECU you can tune in real time. Another place to look is here https://pcmhacking.net/forums/ , depending on what...
  2. Replies
    14
    Views
    2,079

    It may have previously been tuned with HP Tuners...

    It may have previously been tuned with HP Tuners and have one of their custom OS's in there which could explain the unrecognised PCM message
  3. Replies
    6
    Views
    725

    512mb PCM , never really had this much trouble...

    512mb PCM , never really had this much trouble before. At least its done and out of my hair now :beer:
  4. Replies
    6
    Views
    725

    Small update on this. Ended up using Roadrunner...

    Small update on this. Ended up using Roadrunner to tune vehicle. Could bench flash PCM no problem and eventually worked out could read and write to PCM with high speed unchecked. Maybe just a problem...
  5. Replies
    6
    Views
    725

    Gen iii , ls1b. Originally tried with whatever...

    Gen iii , ls1b. Originally tried with whatever version was installed. Updated to RC3 and latest firmware. Still the same.
  6. Replies
    6
    Views
    725

    Bootloader rejected

    Having trouble flashing and reading PCM in a commodore. Keep getting a bootloader rejected or no response from PCM with V7 & V8. Scan tool will connect and work, HP Tuner will read from PCM, any...
  7. No different to any other commodore. Hold the...

    No different to any other commodore. Hold the traction control/esp button down for a bit and all good to go.
  8. Replies
    14
    Views
    7,020

    https://www.dropbox.com/sh/4ydh5wltk3ssxbw/AAAOydq...

    https://www.dropbox.com/sh/4ydh5wltk3ssxbw/AAAOydqwo_stEO4Rs4SRJ9NGa?dl=0
  9. Replies
    7
    Views
    2,004

    If you can post a more accurate location , maybe...

    If you can post a more accurate location , maybe somebody near you could read out your ECM so you can post up here for better advice.
  10. The holley tech doc for the holley 90 throttle...

    The holley tech doc for the holley 90 throttle body shows an idle bleed as in pic attached. Does yours have this? If it does, is it adjusted correctly?
  11. Your log had quite a few EGR codes. Is there any...

    Your log had quite a few EGR codes. Is there any way it could be getting air through the EGR at idle?
  12. Replies
    3
    Views
    1,748

    Try looking at this...

    Try looking at this
    https://www.efilive.com/flashscanv1-supported-vehicles
  13. Replies
    2
    Views
    1,334

    If its an LS1, try looking for B3605 {commanded...

    If its an LS1, try looking for B3605 {commanded fuel when in open loop}. Should be under ,FUEL-MIXTURE. Or put B3605 in the search bar.
  14. I have had this issue as well, usually using IE....

    I have had this issue as well, usually using IE. Use Mozilla firefox without any problems.
  15. Replies
    20
    Views
    2,711

    I have only ever been able to change vin on RR...

    I have only ever been able to change vin on RR using this method - scantool: do Bidirectional->Change VIN, as described by joecar.
    Just remember to have the emulation button activated when making...
  16. Replies
    9
    Views
    1,628

    Have you tried using the speedo calculator in the...

    Have you tried using the speedo calculator in the speedometer/parameters section to adjust your tune? You will maybe have to put "(H0103) Differential Ratio" back to original value before using the...
  17. Replies
    3
    Views
    3,730

    What data are you trying to get from your ecu ?...

    What data are you trying to get from your ecu ? Efilive V4 is only a scan tool.
  18. Replies
    3
    Views
    3,730

    Did you select the VX V6 XML file in the software?

    Did you select the VX V6 XML file in the software?
  19. Replies
    27
    Views
    8,701

    That log file doesn't look too bad. A quick read...

    That log file doesn't look too bad. A quick read of the scan tool PDF will help you understand viewing your logs better and how to use the different dash page.
  20. Replies
    27
    Views
    8,701

    It does add timing, but only to help your car...

    It does add timing, but only to help your car from stalling, depending on the RPM error from desired idle speed. I did make a few other changes. If you do a compare between your file you uploaded and...
  21. Replies
    3
    Views
    1,798

    You say you have a return style fuel system, I...

    You say you have a return style fuel system, I believe from memory your B4001 injector flow rate should be a flat line with the same value in all boxes. Not the sloping line you have which is the way...
  22. Replies
    27
    Views
    8,701

    Try this. I added some spark to your idle...

    Try this. I added some spark to your idle underspeed which was all zero's after about 200rpm error.
  23. Replies
    27
    Views
    8,701

    Whoops, my bad. Yeah I did the wrong file. What...

    Whoops, my bad. Yeah I did the wrong file.
    What are the problems you are having with your idle?
  24. Replies
    27
    Views
    8,701

    AutoVE3.efi, in first post??

    AutoVE3.efi, in first post??
  25. Replies
    27
    Views
    8,701

    First post

    First post
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4