yes, I have. I saw that thread, but it is a different error. everything always ends the same. efilive is for sure seeing the ecm as autodetect is working and it begins to erase but that's as far as i...
Type: Posts; User: comnrailpwr; Keyword(s):
yes, I have. I saw that thread, but it is a different error. everything always ends the same. efilive is for sure seeing the ecm as autodetect is working and it begins to erase but that's as far as i...
Version v8.3.38
Firmware 2.08.194
Boot 2.08.009
2020 Ram 2500 68RFE
Flashed modified file into the truck and went through as expected. Truck would not start and has dash gremlins. Can still...
This should be it. Please post up the CMB, CMC and CME. 24357
Sent from my SM-S906U using Tapatalk
care to share them for your 2015 files? thanks JIM for the 2018 cax.
I'm no help but as long as you have the correct OS base file you can just do a CAL flash and none of the segments will change. This doesn't help if you need to full flash for other reasons though.
...
These are for cmb 5.9 ECM. Likely the same for 6.7 but not sure.
0 00=NOT_SET:
1 01=JCOMTORQ:
2 02=JCOMSPED:
3 03=PSSPEED:
4 04=PTO:
5 05=USERCOMD:
6 06=LIMPHOME:
7 07=ASGTHROT
Just worry about the part numbers. Cvn don't matter. If part numbers match then use what you have.
Sent from my SM-G970U using Tapatalk
As long as both are autos it shouldn't cause any issues. Change vin, flash and go. It's pretty rare for mix matching operating system to cause problems on the pre 2010 trucks. It's worth a shot.
...
Just get rid of them by maxing them out or use them if you want. Your over thinking it. The ECM will use the lowest value of all the limiters.
Sent from my SM-G970U using Tapatalk
Timing bias is not in play if you take care or the limiters. Tune tool has a built in timing calculator now.
Sent from my SM-G970U using Tapatalk
You are correct. DTCs do not control anything. They are just for reporting problems. You are also correct that once you thin the system down to just the engine harness then your anti-theft issue will...
I assume you are using a CMB ECM? If so then literally all you need is a power to the ECM, ground to the ECM, 12v on ignition run and then then crank the motor over and it will start. I don't have...
Have built several standalone setups using late 5.9 ECM. It's not hard to do. The only thing you need is the engine harness and DCM. All the swaps I have done are manual swaps or standalone valve...
The SOTF tuning in the lml isn't true dsp5 like the previous years. It is just switchable fuel limiting. I use fuel temp. Some use egr temp. Log fuel temp and see if it changes when you rotate the...
Good to know. I got it up and running. $100 usd for 3 years imo is worth it if it prevents headaches.
Sent from my SM-G960U using Tapatalk
Tha ks. Signed up for 3 year. It's not bad when you only need to protect 1 device.
Sent from my SM-G960U using Tapatalk
Nailed it paul. Thank you. Something with my antivirus software (free version of avast) is causing the issues. what is weird is it's the same I have had for several years. it appears to be affecting...
I had to right click as well and open in a new window for download.
Sent from my SM-G960U using Tapatalk
Checked permissions. All hass full access. Deleted registry. Re installed and same issues. I can right click in the user config folder and creat new text documents so my account does have access to...
Just installed on my windows tablet without issues so it must me my pc doing something screwy. What is the best way to completely wipe efilive off my pc and start fresh? Only thing I care to keep are...
I tried uninstalling and re installing a few times. I deleted efilive from registry editor. And re installed software. Nothing seems to work. I'm stumped and usually pretty good at this stuff.
...
Yes I am https://uploads.tapatalk-cdn.com/20201112/c2ded015d4140d8ced64cba993f3398e.jpg
Sent from my SM-G960U using Tapatalk
installed the latest version of efilive. now getting this error on v7.5 tune tool. all else seems to work correctly. any ideas? this is the first update i have done since upgrading my machine to...
Generally on the 3rd generation trucks any file will work as long as auto is used for auto, manual file for manual and aisin file for aisin.
No. The autocal can only flash files from the tuner...
https://www.dropbox.com/sh/4ydh5wltk3ssxbw/AAAOydqwo_stEO4Rs4SRJ9NGa?dl=0
Sent from my SM-G960U using Tapatalk