Search:

Type: Posts; User: Age08; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. posted log file in first post, also posted log...

    posted log file in first post, also posted log file after making changes on post 5
  2. Found the problems BTM (B0401/B0402) was kicking...

    Found the problems BTM (B0401/B0402) was kicking in when going under boost and pulling timing and same with B6611/B6614
    Now it holds timing under boost.22900

    22908
  3. When you exceed the ETC max airflow does the...

    When you exceed the ETC max airflow does the computer pull out timing before it goes into limp mode?
  4. it has a couple degrees boost retard setup to...

    it has a couple degrees boost retard setup to just be on the safe side,
    no DTC
    it is setup as SD, no MAF, with 60lb/hr injectors with factory non reference fuel pressure regulator,
  5. 2003 LS1B 0411 COS3 loss of Timing when under boost

    2003 LS1B 0411 COS3 loss of Timing when under boost
    running SD, set burst knock to zero,
    Any Idea's?
    Car is 03 Vette Auto, with LS1 with Ls6 heads and middle cam, with a Vortech supercharger,
    ...
  6. its in a 08 z06 so stock app, tune has been...

    its in a 08 z06 so stock app, tune has been modified to run a cam 227/243 .649/.660 115 lsa,
    I have recently installed a ESC novi 1500 supercharger and 90lb/hr injectors, although this surging...
  7. Looking for a stock LS7 data log at cursing 45-60 km/h

    Looking for a stock LS7 data log at cursing 45-60 km/h,
    maf, map, grams/cyl, rpm, timing, throttle % etc
    I am having issues with part throttle surging, pulling timing out/and back, just what to...
  8. Replies
    1
    Views
    4,218

    PID in V7.5 Not showing up in BBX for e38

    PID in V7.5 Not showing up in BBX for e38
    PID GM.SEMRET is the pid I want to log with flashscan.
    Is there any way to add it to the list for the BB?
  9. Replies
    9
    Views
    1,017

    93.3lb/hr @ 4 Bar, un-referenced as it has the...

    93.3lb/hr @ 4 Bar, un-referenced as it has the reg in the tank, I am using the CALC.WO2BEN,
    It runs decent on with MAF but I get codes for MAP performance.
    I am thinking the MAP maybe shit or its...
  10. Replies
    9
    Views
    1,017

    Thanks Joecar, It works, Have you ever run...

    Thanks Joecar,
    It works,
    Have you ever run into a situation where on e38 the car would run with the yellow wire off of the maf and run fine, but when you would turn off the DIC P0102, P0103 to...
  11. Replies
    9
    Views
    1,017

    I am logging lambda from the west Ecm, and I am...

    I am logging lambda from the west Ecm, and I am using a innovate wide band via serial interface And logging both lambda and afr, I just need help with creating a calculat pid to Create a Ben factor...
  12. Replies
    9
    Views
    1,017

    How setup Cal pid ben to use lambda not afr

    Need help on setup Cal pid ben to use lambda not afr?
    The afr stoich is rescaled by 54.3% due to 92 lb/hr injectors as the 08 e38 has a cap on 8 gram sec on injector size.
  13. Replies
    4
    Views
    1,027

    So this gauge does work for the serial...

    So this gauge does work for the serial communication for the Wide band reading on the Flashscan V2 with the innovate wide band selected on setup.
  14. Replies
    4
    Views
    1,027

    http://www.innovatemotorsports.com/support/manual/...

    http://www.innovatemotorsports.com/support/manual/ECF1_Manual.pdf

    I know under Devices/F8:Serail I/O you would select wide band type: which lists Innovate(LC1,LM1,LM2)

    It would be neat if you...
  15. Replies
    4
    Views
    1,027

    Innovate ECF-1 Ethanol Advance Gauge

    Can the Innovate ECF-1 Ethanol/wide-band 02/ fuel pressure talk to the Flashscan V2 using the serial port the same as the LM-1 for getting Wideband 02 Data?
    Is it possible to gather other data off...
  16. Replies
    14
    Views
    2,992

    That's what I did but it didn't work, I was...

    That's what I did but it didn't work,
    I was using 1.84 as per the difference calculated from the g/s rate used in the FPR to the actual rate.
  17. Replies
    14
    Views
    2,992

    Scaling the IAT Multiplier doesn't seem to work...

    Scaling the IAT Multiplier doesn't seem to work for injector this size.
    The only way that works for me was scaling both the IFR @ 54% and making up the rest with the Stoich,
    I guess the hard limit...
  18. Replies
    14
    Views
    2,992

    attached is modified IAT modifier as well as the...

    attached is modified IAT modifier as well as the injector flow correction from the injectors.
    21677
    I just tried adjusting the stoich_afr my the % difference in IFR and the car idles not bad. The...
  19. Replies
    14
    Views
    2,992

    Joe, what tables do you mean B4001 & B3671? I...

    Joe,
    what tables do you mean B4001 & B3671?
    I have tried the IAT multiply to scale but it doesn't seem to work very if at all, If I understand correctly that IAT multiplier would do this B4001 *...
  20. Replies
    14
    Views
    2,992

    does anyone have a stock tune for 2011 Z06 LS7?

    does anyone have a stock tune for 2011 Z06 LS7?
  21. Replies
    14
    Views
    2,992

    I just read about doing it that way, I was gonna...

    I just read about doing it that way, I was gonna try just with IAT multipler, have you tried this way before?
  22. Replies
    14
    Views
    2,992

    08 E38 LS7 Injector Flow base

    Is there a custom OS that allows larger flow rates for 08 E38?
    Currently in process of installing a blower on LS7 and it came with 80lb@ Bar3 injectors,(plans to run E85 in future).
    I see the...
  23. Thats the exact same thing this is doing, my os...

    Thats the exact same thing this is doing, my os 12612281, the only mode to the car is cam 227/243 .649/.660 115 lsa,
    The cfco is on,
    Ive tried it with/without dfco enable/disable, open/closed...
  24. E38 Light part throttle surge/timing retarding causes?

    E38 on a ls7 light throttle surge/Timing retards around 45-60km/h in 5th gear rpm 1000-1300rpm, I have tired copying high octane timing tables in the area of surge into the coast down timing table,...
  25. Replies
    0
    Views
    472

    E38 LS7 min Air/Idle

    Question when trying to setup min airflow which which column to setup for as it shows 1-6 gear/ park/neutral/reverse? Also how far up in the rpm's do you typically setup for?
    I am having a pain...
Results 1 to 25 of 69
Page 1 of 3 1 2 3