Yes that would work but VE is for airflow and would probably skew some other related tables and transients. I'm already scaling for the 512 g/s airflow. Suppose I could also scale my injector FR...
Type: Posts; User: O1Z06; Keyword(s):
Yes that would work but VE is for airflow and would probably skew some other related tables and transients. I'm already scaling for the 512 g/s airflow. Suppose I could also scale my injector FR...
I am setting up an E85 only tune, manually not flex fuel, on the 02020005 OS and I have done a few searches where all I need to change is B3601 to the stoich ratio of the blend used (using an...
Ok so now I think it's working.:doh:
I was using the scan tool to check SRT's after evey flash I made to see if the SRT changed to ready. I then was looking at SMS (Mode $05) and tests were...
Looking again it's all the MAFs P0101 through P0103. I think I tried that way back when and the car would not start because it would not fail into speed density backup. I'm curious now so I may try...
I found the DTC table herehttp://www.gearchatter.com/viewtopic10274.php
AIR - P0410, P1415 or P1416
Catalyst - P0420 or P0430
EVAP - P0440, P0442, P0446, P1441
Oxygen Sensor - P0133 or P0153,...
Hi all, I need some help here. I am having some problems with not ready SRT for Evap, SAIR and O2 sensor 2.
I need to get it inspected to get my registration for my specialty licence plate. I live...
Hi Joe, yes it's an 01-04.
I would think the RR battery is there for like you said to keep the volatile RAM from being lost. Things like crank reluctor signature, vin, vats, and of course the...
What is node DSW?
Hi all, I have been having a bit of trouble recently after I set a reduced engine power after modifying the ETC traction control table. I immediately set the values back to original and reflashed the...
Can you try your original cax file with the "allow cax option" checked and see if you get any error messages?
Use cax b above, it's for 12212156 os with the overlapping addresses removed.
Well today I ended up not being able to recover my PCM. I did a full flash last week after some cax updates and noticed that my VIN was not being saved in the PCM. So I tried V7.5 to full flash an...
You're running a MAF? Can you try OLSD COS3/5?
Made a few minor changes to the folders.
Joecar, please move this thread to the .cax forum if you want.
Cheers,
Jesse
Well, I think I got it sorted. I modified the .cax and removed all the overlapping addresses from post 1.
B9014 and B9021 are the ones that confused me the most because they had the same address...
I set it to the min pulse width from B4003. Have a look here http://forum.efilive.com/showthread.php?13364-IBPW-B4005-B3701-correlation/page2&highlight=b9021
The modifiers for transient fuel based on airflow and the duplicate boiling/impact/stomp tables were under a new folder called transient fuel. The fuel/dynamics section was not changed.
Loaded Micks "cax b" and now have B9021 but would like to have all the transient modifiers. Im still trying to fix a lean spike on tip out.
Hey Joe, so I was just looking over my 02020005.cax file and noticed that the addresses for B9014 and B9021 are the same, (B632). Also my cal_link link file does not have B9013 and B9021. What does...
I used the min pulse in B9021 and fixed the rich decel.
I think your hitting the PCM limit B9021 which you can't adjust without the .cax.
Thanks Ross. That is interesting about how it works but a bit over my head. I would sometimes see B9021 get reset back to its default value after a write so I would just check it every time. So now I...
Would have posted in cax forum but didn't see any recent activity. Please move as required.
Just updated to V7.5.7.233 and the .cax calibration address are now overlapping. I tried a fresh .cax...
What injectors? I have ID1000s and they give you injector data for alot of different MAP pressures. I would have a look at their spreadsheet and see what changes per different MAP. My MAP referenced...
Paul, thank you for the quick response and your help finding the bug.
If it is any coincidence, sometimes I have a bootloader reject after step 1. This happens if I try to flash with V7 after...