Thanks for the help. I had no clue about the Controller Authorization. I'm still under warranty so I just wanted to pull the tune to take a look and patiently wait for the warranty to expire. Do...
Type: Posts; User: Gregs; Keyword(s):
Thanks for the help. I had no clue about the Controller Authorization. I'm still under warranty so I just wanted to pull the tune to take a look and patiently wait for the warranty to expire. Do...
I just bought a 2019 cruze 1.6 diesel. I've been reading the forums trying to understand the tuning process and have run into conflicting info.
Do I need to find a supplier for the stock tune...
Thanks for the replies. I got the cam swap done and retained VVT. It runs ok on the stockish tune but LTFTs are running -9 with lightdiving. Haven't opened it wide open yet. The wideband is still...
I gave up on this but am at the point where I need a calc_pids file for my 2010 tahoe 5.3. It's an E38 controller. I need something that I can use with my AEM wideband with analog output.
Thanks for the info, i will checkout the writeup on g8nation. It's too cold to do a conversion in an unheated garage right now. I may end up disabling flex fuel until this spring when it warms up...
Thanks,
I see there is a toggle button in the tune to specify calculation vs physical sensor. Does anyone know if it's possible to convert to a real sensor and which pins on the PCM I would need...
Just want to verify that i'm reading this correct, we should only click reset if the ethanol percent is less than 10% but greater than 0%. Here is a pic of the button in the DVT control panel.
...
I see you have 0Hz for the MAF fail. Have you tried 1Hz instead? Is the MAF unplugged? Are you getting a MIL for the MAF being failed? You should be getting a check engine light if the MAF is...
got it figured out!
Short story: There are two calc_pids.txt files. The one you need to modify is located in C:\Users\<username>\Documents\EFILive\V7.5\User Configuration
Long story: I put...
Hey guys,
I have a new computer and I lost my calc_pids file that was working. In the past I've had really bad luck getting my calc_pids.txt right. I've tried about a dozen calc_pids.txt files...
After your first post I went and opened a newer log file that was similar in size and it loaded up quick in V8. I guess it's time for me to get with the times and start using V8. I haven't been in...
Paul,
The file it too large for email, here is a dropbox link to the file. I have issues with both large and small files., scan tool version is 7.5.28 ...
I'm running the latest public release software. I'm having an issue where when I load a log file it asks me if I want to replot the log file since it has over 3000 frames. I click "no" and it...
All,
I don't know if this is the right place to ask or not. Before winter hits I'm thinking about installing an aftermarket remote start in the truck. Does anyone know if removing the antitheft...
That did the trick, I will checkout my other analog ports to see if they have voltage when not being used.
Attached is the calc_pids I have that seem to be working but with all the problems you've identified. I'm using LS1B only.
On a separate topic I'm finding that the voltage being logged is too...
Could I please get some help with syntax,
Why does this work:
V 0.0 5.0 .3 "{EXT.AD1}"
AFR 10.0 20.0 .3 "{EXT.AD1}*2.3750+7.3125"
LAM 0.5 1.5 .3 "(0.1621*{EXT.AD1})+0.4990"...
Today I wired up for analog voltages, I've given up on serial since I can't get it to work at all. It's been cold here in Iowa and working in an unheated garage isn't fun, finally getting around to...
I finally got a nice day to do some testing, the multimeter shows .03V from ground to serial output on the wideband. Using Putty I couldn't get any output. I tried a bunch of settings, tried it...
Dummy me, I should have checked for voltage while I was there
I can do this
No luck, I switched AEM output to V2 pin 2 (tx). V2 still doesn't read the wideband.
Thanks, I'll try this tonight
Nice diagram! I'm at work and my connector is at home but I think my ground was white on the connector going into the V2. See attached graphic I stole from the forum, I took that diagram as looking...
AEM Pin #5 (Serial/RS-232 Output) to Flashscan V2 pin #1 (RX)
Hi all,
I'm getting started back up after a few years out of the game. I got a new AEM x-series wideband installed last week. I used to tune with an LC-1 but it died a few years ago. The new...